Heater Hoses Replacement - Auxiliary Suburban-Front

1. Raise the vehicle.

Support the vehicle with suitable safety stands. Refer to Lifting and Jacking the Vehicle

2. Drain the engine coolant. Refer to Cooling System Draining and Filling
3. Remove the right front wheelhouse. Refer to Front Fender Replacement in Body Front End.



4. Remove the bolts in the engine compartment.
5. Remove the hose (1,2) clamps in the engine compartment.



6. Remove the bolts from the frame.
7. Remove the hose clamps from the frame.



8. Disconnect the heater inlet hose (1) from the tee fittings.
9. Disconnect the heater outlet hose (2) at the tee fittings.

1. Connect the heater outlet hose (2) to the tee fittings.
2. Connect the heater inlet hose (1) to the tee fittings.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the hose (1,2) clamp bolts in the engine compartment.

Tighten
Tighten the bolts to 17 N·m (13 lb ft).




4. Install the hose clamp bolts on the frame.

Tighten
Tighten the bolts to 17 N·m (13 lb ft).

5. Install the right front wheelhouse. Refer to Front Fender Replacement in Body Front End.
6. Add the engine coolant. Refer to Cooling System Draining and Filling
7. Lower the vehicle.
8. Inspect the system for leaks.

Heater Hoses Replacement - Auxiliary Suburban-Rear

Tools Required

J 38723 Heater Line Quick Connect Separator

1. Raise the vehicle.

Support the vehicle with suitable safety stands. Refer to Lifting and Jacking the Vehicle

2. Drain the engine coolant. Refer to Cooling System Draining and Filling
3. Remove the bolts.



4. Perform the following steps in order to disconnect the rear hose assembly (2) from the front hose assembly.

4.1.	Push the rear hose assembly (2) into the front hose assembly.

4.2.	Insert the J 38723 into the hose in order to release the locking tabs.

5. Perform the following steps in order to disconnect the rear hose assembly from the auxiliary heater core (4).

5.1.	Push the rear hose assembly into the auxiliary heater core.

5.2.	Insert the J 38723 into the hose in order to release the locking tabs.

1. Push the rear hose assembly (2) into the front hose assembly until the retainer tabs lock in order to connect the hose assemblies.
2. Push the rear hose assembly (2) into the auxiliary heater core (4) until the retainer tabs lock in order to connect the hoses with the heater core.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the bolts.

Tighten
Tighten the bolts to 17 N·m (13 lb ft).

4. Add the engine coolant. Refer to Cooling System Draining and Filling
5. Lower the vehicle.
6. Inspect the system for leaks.

Heater Hoses Replacement - Auxiliary Diesel-Rear

1. Raise the vehicle.

Support the vehicle with suitable safety stands. Refer to Lifting and Jacking the Vehicle

2. Drain the engine coolant. Refer to Cooling System Draining and Filling



3. Remove the right front wheelhouse. Refer to Front Fender Replacement in Body Front End.
4. Remove the bolts in the engine compartment.
5. Remove the hose clamps in the engine compartment.



6. Remove the bolts from the frame.
7. Remove the hose clamps from the frame.



8. Disconnect the heater inlet (1) hose from the tee fittings.
9. Disconnect the heater outlet (2) hose at the tee fittings.

1. Connect the heater outlet (2) hose to the tee fittings.
2. Connect the heater inlet (1) hose to the tee fittings.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the hose clamp bolts in the engine compartment.

Tighten
Tighten the bolts to 17 N·m (13 lb ft).




4. Install the hose clamp bolts on the frame.

Tighten
Tighten the bolts to 17 N·m (13 lb ft)

5. Install the right front wheelhouse. Refer to Front Fender Replacement in Body Front End.
6. Add the engine coolant. Refer to Cooling System Draining and Filling
7. Lower the vehicle.
8. Inspect the system for leaks.