GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2000 🢒 Tahoe - 4WD 🢒 Steering 🢒 Steering Wheel and Column - Tilt 🢒 Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle

Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Floor Shift


    Object Number: 293254 Size: SH
  1. Align the block tooth on the steering column shaft assembly (1) to the 12 o'clock position.
  2. Place the ignition switch in the LOCK position and remove the key.

    3. Object Number: 293252 Size: SH
  3. Install the wave washer (1) onto the steering column shaft assembly (2).
  4. If you are installing the existing inflatable restraint steering wheel module coil, you must center the inflatable restraint steering wheel module coil first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .

    5. Object Number: 322951 Size: SH

    Important: A new inflatable restraint steering wheel module coil will be pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.

  5. Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
  6. Slide the new inflatable restraint steering wheel module coil (4) onto the steering column shaft assembly (2).
  7. Firmly seat the retaining ring (3) into the groove on the steering column shaft assembly (2).
  8. Remove the centering tab from the new inflatable restraint steering wheel module coil (4).
  9. Discard the centering tab.

    10. Object Number: 322946 Size: SH
  10. Reconnect the inflatable restraint steering wheel module coil connector to the turn signal switch assembly connector.

    11. Important: The abrasion sleeve must be installed back onto the steering column wire harness assembly. The electronic lock module assembly wires and connector must be hanging out of the middle of the abrasion sleeve.

  11. Attach the wire harness assembly (1) to the wire restraint clip (2).
  12. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  13. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System .

Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Column Shift


    Object Number: 293254 Size: SH
  1. Align the block tooth on the steering column shaft assembly (1) to the 12 o'clock position.
  2. Place the ignition switch in the LOCK position.

    3. Object Number: 293252 Size: SH
  3. Install the wave washer (1) onto the steering column shaft assembly (2).
  4. If you are installing the existing inflatable restraint steering wheel module coil, you must center the inflatable restraint steering wheel module coil first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .

    5. Object Number: 415291 Size: SH

    Important: The new inflatable restraint steering wheel module coil will be pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.

  5. Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
  6. Slide the new inflatable restraint steering wheel module coil (4) onto the steering column shaft assembly (2).
  7. Firmly seat the retaining ring (3) into the groove on the steering column shaft assembly (2).
  8. Remove the centering tab from the new inflatable restraint steering wheel module coil (4).
  9. Discard the centering tab.

    10. Object Number: 415293 Size: SH

    Important: The abrasion sleeve must be installed back onto the steering column wire harness assembly. The electronic lock module assembly wires and connector must be hanging out of the middle of the abrasion sleeve.

  10. Reconnect the inflatable restraint steering wheel module coil connector to the turn signal switch assembly connector.
  11. Install the wire harness assembly (1) into the wire harness strap(2).
  12. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  13. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System .

Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Export


    Object Number: 293254 Size: SH
  1. Align the block tooth on the steering column shaft assembly (1) to the 12 o'clock position.
  2. Place the ignition switch in the LOCK position.

    3. Object Number: 293252 Size: SH
  3. Install the wave washer (1) onto the steering column shaft assembly (2).
  4. If you are installing the existing inflatable restraint steering wheel module coil, you must center the inflatable restraint steering wheel module coil first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .

    5. Object Number: 415291 Size: SH

    Important: A new inflatable restraint steering wheel module coil will be pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.

  5. Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
  6. Slide the new inflatable restraint steering wheel module coil (4) onto the steering column shaft assembly (2).
  7. Firmly seat the snap ring (3) into the groove on the steering column shaft assembly (2).
  8. Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).

    9. Object Number: 415293 Size: SH
  9. Reconnect the inflatable restraint steering wheel module coil connector to the turn signal switch assembly connector.
  10. Attach new wire harness strap (2) to the wire harness assembly (1) and the steering column.
  11. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .