The drive motor position sensor is monitored by the motor control module (MCM). The MCM monitors the angular position, speed and direction of the drive motor generator based upon the signals of the resolver-type position sensor. The position sensor, or resolver, contains a drive coil, two driven coils and an irregular shaped metallic rotor. The metallic rotor is mechanically attached to the shaft of the drive motor generator. At ignition ON, the MCM outputs a 7 volt ac, 10 kHz excitation signal to the drive coil. The drive coil excitation signal creates a magnetic field surrounding the two driven coils and the irregular shaped rotor. The MCM then monitors the two driven coil circuits for a return signal. The position of the irregular shaped metallic rotor causes the magnetically-induced return signals of the driven coils to vary in size and shape. A comparison of the two driven coil signals allows the MCM to determine the exact position, speed and direction of the drive motor generator.

The ignition is ON.

The MCM cannot track the motor position.

DTCs P1B03 and P1B04 are Type A DTCs.

Schematic Reference

Hybrid Controls Schematics

Connector End View Reference

Electrical Information Reference

Special Tools

DT-48493 Jumper Harness

Note: The drive motor generator position sensor circuits require proper circuit integrity for correct system operation. Just a few ohms of additional circuit resistance may cause position sensor signal degradation.

•	Always inspect position sensor signal connectors for proper terminal contact.

•	All diagnostic connections must be made with the approved test probes to prevent the creation of poor terminal contact.

•	Connectors that contain position sensor signal circuits must always be clean and dry prior to mating. Foreign material or moisture within the connector may cause sensor signal degradation.

1. Ignition OFF, disconnect PIM X1 connector.
2. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the PIM X1 circuits as indicated. Use the specifications for the drive motor generator that set the DTC. Also test each circuit for a short to ground.

⇒	If any of the circuits are not within specification, continue with testing.

⇒	If all circuits test normal, inspect for proper terminal contact at PIM X1 connector. If PIM X1 terminal contact tests OK, perform the Intermittent Condition Testing below.

3. Disconnect the transmission X176 24-way connector.
4. Connect the DT-48493 to the X176 24-way connector at the transmission.
5. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the transmission X176 circuits as indicated. Use the specifications for the drive motor generator that set the DTC. Also test each circuit for a short to ground.

⇒	If all circuits test normal, continue with testing.

⇒	If any of the circuits are not within specification, test the internal transmission harness for the condition. If the internal transmission harness tests OK, replace the applicable drive motor generator.

6. Disconnect DT-48493 from the transmission X176 24-way connector.
7. Connect DT-48493 to the transmission X176 24-way connector at the vehicle harness.
8. Disconnect PIM connector X1.
9. Using the PIM to Transmission Terminal Reference table listed below, test the vehicle harness continuity between PIM X1 and transmission X176. Use the specifications for the drive motor generator that set the DTC. Also test these circuits for short to ground and to the shield circuit if the shield circuit is not presently grounded to the PIM assembly.

⇒	If any of the circuits are not within the specified range, repair or replace the wiring harness.

⇒	If all circuits test normal, inspect transmission connector X176 for proper terminal contact. If transmission connector X176 tests OK, inspect the harness for an intermittent concern.

1. If possible, determine which of the position sensor circuits have the intermittent condition by reviewing the Diagnostic Fault Information table. For example, DTCs P0C57 and P0C52 only set for a short to ground condition on either the S1 or S3 circuit.
2. Using the Position Sensor Specification table listed below, monitor the position sensor circuits at PIM X1 connector while manipulating the applicable harness and connectors.

⇒	If any of the circuits are not within specification, repair the harness or terminal as required. If a harness repair is indicated and external harness damage is not evident, the most likely location for internal wire damage is near the harness clamping locations.

3. Disconnect transmission X176 connector and inspect for the following:

•	Proper terminal contact

•	Proper terminal retention in the connector

•	Foreign material or moisture

⇒	Repair, replace or clean the connector as appropriate.

4. Reconnect all connectors and test drive the vehicle.

⇒	If the DTC sets, replace the applicable drive motor generator and retest for DTCs. If the DTC sets, replace the PIM.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.