• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
Front Vertical Up Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Front Vertical Down Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Rear Vertical Up Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Rear Vertical Down Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Horizontal Forward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Horizontal Rearward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Recline Forward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Recline Rearward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
1. Power seat inoperative 2. Scan tool does not communicate with low speed GMLAN device |
When the power seat switches are pressed, they send a 12-volt signal through the switch signal circuits to the memory seat module (MSM). The MSM then commands the driver seat motors to move in response to the switch signals.
The memory seat module must be powered.
• | If a seat switch circuit is active in one direction and the switch for the opposite direction is pressed, this DTC will set. |
• | Multiple DTCs will set if one of the switch signal circuits is shorted to voltage. |
• | A motor output driven in response to a switch considered failed, is deactivated for both directions. |
• | All memory recall commands are ignored. |
• | The MSM will respond to any other switch signal that has not set a DTC. |
• | The current DTC will clear and set the code to history, 3 seconds after the fault is no longer present and the ignition is cycled OFF then back to ACC or RUN. |
• | A history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Memory Seats Description and Operation
Control Module References for Scan Tool Information
Ignition ON, observe all scan tool Driver Position Module seat switch parameters while pressing and releasing the each seat directional switch. The reading should change between Inactive and Active.
• | Front Vertical Upward Switch |
• | Front Vertical Downward Switch |
• | Rear Vertical Upward Switch |
• | Rear Vertical Downward Switch |
• | Horizontal Forward Switch |
• | Horizontal Rearward Switch |
• | Recline Forward Switch |
• | Recline Rearward Switch |
⇒ | If not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the MSM. |
• | Front vertical upward switch terminal A |
• | Front vertical downward switch terminal K |
• | Rear vertical upward switch terminal F |
• | Rear vertical downward switch terminal J |
• | Horizontal forward switch terminal D |
• | Horizontal rearward switch terminal C |
• | Recline forward switch terminal H |
• | Recline rearward switch terminal G |
• | Front vertical upward switch terminal A |
• | Front vertical downward switch terminal K |
• | Rear vertical upward switch terminal F |
• | Rear vertical downward switch terminal J |
• | Horizontal forward switch terminal D |
• | Horizontal rearward switch terminal C |
• | Recline forward switch terminal H |
• | Recline rearward switch terminal G |
⇒ | If not the specified value, replace the seat adjuster switch. |
• | Front vertical upward switch terminal A |
• | Front vertical downward switch terminal K |
• | Rear vertical upward switch terminal F |
• | Rear vertical downward switch terminal J |
• | Horizontal forward switch terminal D |
• | Horizontal rearward switch terminal C |
• | Recline forward switch terminal H |
• | Recline rearward switch terminal G |
⇒ | If greater than the specified range, replace the adjuster switch switch. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• | Control Module References for MSM replacement, setup, and programming |