Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B3205 00: Window Inactive Over Current FaultDTC B3205 0B: Window Motor Fast Over Current Fault
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Driver Door Switch B+ | U0199 00 | U0199 00 | -- | -- |
LR Window Switch B+ | 1, 3 | 3 | -- | -- |
Passenger Door Switch B+ | U0200 00 | U0200 00 | -- | -- |
RR Window Switch B+ | 2, 4 | 4 | -- | -- |
Power Window Switch Right Rear Down Signal | B3823 00 | B3823 00 | B3823 00 | -- |
Power Window Switch Right Rear Up Signal | B3822 00 | B3822 00 | B3822 00 | -- |
Power Window Switch Left Rear Down Signal | B3820 00 | B3820 00 | B3820 00 | -- |
Power Window Switch Left Rear Up Signal | B3819 00 | B3819 00 | B3819 00 | -- |
Power Window Lockout Left Rear Control | B3821 00 | B3821 00 | B3821 00 | -- |
Power Window Lockout Right Rear Control | B3824 00 | B3824 00 | B3824 00 | -- |
LR Window Motor Control | 3 | 3 | 3 | -- |
Passenger Window Motor Control | B3205 00 | B3205 0B | B3205 00 | -- |
RR Window Motor Control | 4 | 4 | 4 | -- |
Driver Window Motor Control | B3205 00 | B3205 0B | B3205 00 | -- |
LR Window Switch Ground | -- | 3 | 3 | -- |
RR Window Switch Ground | -- | 4 | 4 | -- |
Driver Door Switch Ground | -- | U0199 00 | 1 | -- |
Passenger Door Switch Ground | -- | U0200 00 | 2 | -- |
1. Driver Window Malfunction 2. Passenger Window Malfunction 3. Left Rear Window Malfunction 4. Right Rear Window Malfunction | ||||
Circuit/System Description
The driver door switch (DDS) and passenger door switch (PDS) control the power window functions through the power window motor up and down control circuits. The door switches monitor the control circuits for fault conditions when up or down operation is requested prior to activating the function and during operation.
Conditions for Running the DTC
| • | Battery voltage must be between 9-16 volts. |
| • | The ignition is ON. |
Conditions for Setting the DTC
B3205 00
The DDS or PDS detects a short to ground or short to voltage on their respective window motor control circuit.
B3205 0B
The DDS or PDS has detected excessive current flow on their respective window motor control circuit.
Action Taken When the DTC Sets
The affected power window will be inoperative.
Conditions for Clearing the DTC
| • | The DTC will be current for as long as the fault is present. |
| • | When the fault is no longer present, the DTC will be a history DTC. |
| • | A history DTC will clear after 50 ignition cycles. |
Diagnostic Aids
B3205 0B can be set due to excessive physical resistance in the window regulator assembly. Ensure proper mechanical operation of the regulator assembly prior to replacing electrical components.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Power Windows Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Observe the operation of the power windows while commanding each window UP and DOWN by using their respective window switches, each window should perform the UP and DOWN function.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the appropriate window motor.
- Connect a test lamp between control circuit terminal A and control circuit terminal B.
- Ignition ON, command the window UP and DOWN by using the door switch. The test lamp should turn ON when commanding the UP and DOWN states.
- If all circuits test normal, test or replace the window motor.
| ⇒ | If the test lamp is always OFF during either of the commands, test either control circuit for a short to ground or open/high resistance. If the circuits test normal, replace the door switch. |
| ⇒ | If the test lamp is always ON, test either control circuit for a short to voltage. If the circuits test normal, replace the door switch |
Component Testing
Important: When performing the following tests, make sure that the window motor is not all ready in the position the test is attempting to produce.
- Ignition OFF, disconnect the harness connector at the appropriate window motor.
- Install a 25A fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The window motor should perform the UP or DOWN function.
- Reverse the jumper wires; the window motor should perform the DOWN or UP function.
| ⇒ | If the function does not perform as specified, replace the window motor. |
| ⇒ | If the function does not perform as specified, replace the window motor |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for DDS and PDS replacement, setup, and programming |
