Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B3920 01: Group 1 Seat Motors Common Circuit Short to BatteryDTC B3920 02: Group 1 Seat Motors Common Circuit Short to Ground
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
Adjustable Pedal Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 3 | B3920 01 | B1340 42, B1340 4B, B3606 5A |
Adjustable Pedal Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 3 | B3920 01 | B1340 42, B1340 4B, B3606 5A |
Driver Seat Front Vertical Motor Down Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2355 5A |
Driver Seat Front Vertical Motor Up Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2355 5A |
Driver Seat Rear Vertical Motor Down Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2365 5A |
Driver Seat Rear Vertical Motor Up Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2365 5A |
Driver Seat Horizontal Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2375 5A |
Driver Seat Horizontal Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2375 5A |
Driver Seat Recline Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B1825 5A |
Driver Seat Recline Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B1825 5A |
Driver Seat Lumbar Motor Up Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1340 42, B1340 4B, B1860 5A |
Driver Seat Lumbar Motor Down Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1340 42, B1340 4B, B1860 5A |
Driver Seat Lumbar Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1850 5A |
Driver Seat Lumbar Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1850 5A |
1. Power seat motor inoperative 2. Lumbar motor inoperative 3. Adjustable motor inoperative | |||||
Circuit/System Description
The memory seat module (MSM) controls the seat, recline, lumbar, and adjustable pedal motors via half bridges that are connected to a common power rail internal to the module. The MSM connects all of the motor control circuits to a common reference point whenever they are not in operation. This reference point is biased to approximately 2.5 volts. The MSM checks to see if this reference voltage is shorted to ground or battery before enabling any seat, lumbar, or adjustable pedal motor.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
B3920 01
The voltage on any power rail 1 motor control circuit exceeds 2.78 volts for 100 ms.
B3920 02
The voltage on any power rail 1 motor control circuit is below 1.47 volts for 100 ms.
Action Taken When the DTC Sets
The MSM will not allow operation of any motor on the power rail for which the DTC was set.
Conditions for Clearing the DTC
| • | The current DTC clears when the malfunction is no longer present and the power mode changes to OFF then back to ACC or RUN. |
| • | A history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Memory Seats Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the X1 harness connector at the MSM.
- Ignition ON, verify that a test lamp does not illuminate between the control circuits listed below and ground:
- Test for infinite resistance between the control circuits listed below and ground:
- Ignition OFF, disconnect the X4 harness connector at the MSM.
- Ignition ON, verify that a test lamp does not illuminate between the control circuits listed below and ground:
- Test for infinite resistance between the control circuits listed below and ground:
- If all circuits test normal, replace the MSM.
| • | Front vertical motor terminal 12 |
| • | Front vertical motor terminal 13 |
| • | Rear vertical motor terminal 15 |
| • | Rear vertical motor terminal 16 |
| • | Seat horizontal motor terminal 9 |
| • | Seat horizontal motor terminal 10 |
| ⇒ | If the test lamp illuminates, test the control circuit for a short to voltage. |
| • | Front vertical motor terminal 12 |
| • | Front vertical motor terminal 13 |
| • | Rear vertical motor terminal 15 |
| • | Rear vertical motor terminal 16 |
| • | Seat horizontal motor terminal 9 |
| • | Seat horizontal motor terminal 10 |
| ⇒ | If not the specified value, test the control circuit for a short to ground. |
| • | Lumbar vertical motor terminal 1 |
| • | Lumbar vertical motor terminal 2 |
| • | Lumbar horizontal motor terminal 12 |
| • | Lumbar horizontal motor terminal 13 |
| • | Seat recline motor terminal 15 |
| • | Seat recline motor terminal 16 |
| • | Adjustable pedal actuator terminal 9 |
| • | Adjustable pedal actuator terminal 10 |
| ⇒ | If the test lamp illuminates, test the control circuit for a short to voltage. |
| • | Lumbar vertical motor terminal 1 |
| • | Lumbar vertical motor terminal 2 |
| • | Lumbar horizontal motor terminal 12 |
| • | Lumbar horizontal motor terminal 13 |
| • | Seat recline motor terminal 15 |
| • | Seat recline motor terminal 16 |
| • | Adjustable pedal actuator terminal 9 |
| • | Adjustable pedal actuator terminal 10 |
| ⇒ | If not the specified value, test the control circuit for a short to ground. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for the MSM replacement, programming and setup |
