GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Tracker - 4WD 🢒 Engine 🢒 Engine Electrical 🢒 Fuel Injector Circuit Diagnosis

Circuit Description

The powertrain control module (PCM) controls each individual fuel injector sequentially. The PCM energizes the solenoid coil of the fuel injectors. When energized the fuel injector solenoid operates the solenoid plunger allowing pressurized fuel to be injected into the intake port of the cylinder. The fuel pump will pressurize the fuel rail and the fuel injectors as long as the engine is cranking, and the PCM is receiving ignition system reference pulses. The fuel pump will stop after 2 seconds if the PCM does not receive any ignition system reference pulses.

Diagnostic Aids

Check for any of the following conditions:

    • Water, foreign material, or stale fuel can cause a no start or a hard start condition.
    • Erratic fuel pressure or a restricted fuel filter may cause a no start or a hard start condition.
    • Faulty fuel injectors -- There may be fuel spray at the fuel injectors, but it may not be enough to start the engine. Normal fuel injector resistance is 13-16 ohms at 20°C (68°F). If the fuel injectors and their circuits are OK, and fuel spray is detected, the fuel injector nozzle may be partly blocked or restricted.

An intermittent malfunction may be caused by a fault in the fuel injector sensor circuit. Inspect the wiring harness and components for an intermittent condition. Refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. The Diagnostic System Check-Engine Controls prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.

    2.

  2. This step checks if the PCM is controlling the fuel injector signals.

    3.

  3. This step checks for a short in the fuel injector control circuit.

    4.

  4. This step checks for voltage at the fuel injector.

    5.

  5. This step checks for an open in fuel injector control circuit or for a faulty PCM.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: This table assumes that the malfunction indicator lamp (MIL) and the data link connector (DLC) function normally. Check that MIL operation and DLC communication is OK before proceeding.

  1. Turn OFF the ignition.
  2. Disconnect all four fuel injector electrical connectors.
  3. Install a J 34730-2B injector test lamp or an equivalent into each fuel injector harness connector.
  4. Observe the injector test lamp for each injector while cranking the engine.

Did the injector test lamp flash for each injector while cranking the engine?

Go to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F)

Go to Step 3

3

Was the injector test lamp illuminated all the time, for any injector circuit, while cranking the engine?

Go to Step 4

Go to Step 5

4
  1. Check for a short to ground in the faulty fuel injector control circuit between the PCM and the fuel injector.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.

Was a repair necessary?

Go to Step 11

Go to Step 10

5

  1. Remove the injector test lamp from the fuel injector electrical connector.
  2. Connect a test lamp from ground to the ignition positive voltage side of the fuel injector harness connector that did not flash.
  3. Turn ON the ignition, leaving the engine OFF.

Did the test lamp illuminate?

Go to Step 6

Go to Step 8

6

  1. Connect one end of a test lamp to the control side of the fuel injector harness connector that did not flash.
  2. Connect the other end of the test lamp to B+.
  3. Observe the test lamp while cranking the engine.

Does the test lamp flash while cranking the engine?

Go to Step 7

Go to Step 9

7

Repair the faulty electrical connections at the fuel injector harness connector. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 11

--

8

Repair the open in the ignition feed circuit between the fuel injector and the main relay. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 11

--

9
  1. Check for an open in the faulty fuel injector control circuit.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.
  3. Repeat steps 2 thru 9 until the injector test lamp flashes in all 4 fuel injector circuits.

Was a repair necessary?

Go to Step 11

Go to Step 10

10

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

Go to Step 11

--

11

Operate the vehicle within the conditions under which the original symptom was noted.

Does the system now operate properly?

System OK

Go to Diagnostic Aids