Power Steering Gear Inlet Pipe/Hose Replacement 2.0L

1. Place a drain pan under the vehicle in order to catch any escaping fluid.

Notice: Refer to Power Steering Hose Disconnected Notice in the Preface section.





Important: The first design banjo bolt style fitting utilizes 2 gaskets. The second design flare nut style fitting utilizes seals.

2. Remove the following components from the steering gear:

•	The power steering gear inlet hose fitting (5)

•	The 2 gaskets, if equipped

•	The power steering gear inlet hose (6)




3. Remove the power steering gear inlet hose fitting from the power steering pump (1).
4. Remove the power steering gear inlet hose and the 2 gaskets from the power steering pump.
5. Remove the power steering gear inlet hose from the bracket.

Notice: Refer to Fastener Notice in the Preface section.

Notice: Refer to Installing Hoses without Twists or Bends Notice in the Preface section.




1. Install the following components to the power steering pump (1):

•	The power steering gear inlet hose

•	The 2 gaskets

•	The fitting

Tighten
Tighten the fitting to 60 N·m (43.5 lb ft).





Important: The first design banjo bolt style fitting uses 2 gaskets. The second design flare nut style fitting uses seals. The first design power steering components are not interchangeable with the second design power steering components.

2. Install the following components to the steering gear:

•	The steering gear inlet hose (6)

•	The 2 gaskets, if equipped

•	The fitting (5)

Tighten
Tighten the fitting to 35 N·m (25.5 lb ft).

3. Install the power steering gear inlet hose to the hose bracket.

Notice: Refer to Using Proper Power Steering Fluid Notice in the Preface section.

4. Add fluid to the reservoir. Refer to Checking and Adding Power Steering Fluid .

Notice: Refer to Air in the Power Steering System Notice in the Preface section.

5. Bleed the power steering system. Refer to Power Steering System Bleeding .

Power Steering Gear Inlet Pipe/Hose Replacement 2.5L

1. Place a drain pan under the vehicle in order to catch any escaping fluid.

Notice: Refer to Power Steering Hose Disconnected Notice in the Preface section.





Important: The first design banjo bolt style fitting utilizes 2 gaskets. The second design flare nut style fitting utilizes seals.

2. Remove the following components from the steering gear:

•	The power steering gear inlet hose fitting (5)

•	The 2 gaskets, if equipped

•	The power steering gear inlet hose (6)




3. Remove the power steering gear inlet hose fitting from the power steering pump (3).
4. Remove the power steering gear inlet hose (4) and the 2 gaskets from the pump.

Notice: Refer to Fastener Notice in the Preface section.

Notice: Refer to Installing Hoses without Twists or Bends Notice in the Preface section.




1. Install the following components to the power steering pump (3):

•	The power steering gear inlet hose (4)

•	The 2 gaskets

•	The fitting

Tighten
Tighten the fitting to 60 N·m (43.5 lb ft).





Important: The first design banjo bolt style fitting uses 2 gaskets. The second design flare nut style fitting uses seals. The first design power steering components are not interchangeable with the second design power steering components.

2. Install the following components to the steering gear:

•	The steering gear inlet hose (6)

•	The 2 gaskets, if equipped

•	The fitting (5)

Tighten
Tighten the fitting to 35 N·m (25.5 lb ft).

Notice: Refer to Using Proper Power Steering Fluid Notice in the Preface section.

3. Add fluid to the reservoir (6). Refer to Checking and Adding Power Steering Fluid .

Notice: Refer to Air in the Power Steering System Notice in the Preface section.

4. Bleed the power steering system. Refer to Power Steering System Bleeding .