GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2004 🢒 Tracker - 4WD 🢒 DTC 🢒 DTC P0717

Circuit Description

The powertrain control module (PCM) monitors the following conditions:

    • The transmission input speed
    • The engine speed
    • The vehicle speed
    • The gear position

The PCM compares the vehicle speed with the input/turbine speed sensor.

Conditions for Setting the DTC
    • Input/turbine speed sensor detected speed is lower than 63 RPM while the vehicle is running under all the following conditions:
       - Vehicle speed is higher than 10 km/h (7 mph) with 1st gear held in Drive range for 1 second or more.
       - Vehicle speed is higher than 20 km/h (13 mph) with 2nd gear held in Drive range for 2 seconds or more.
       - Vehicle speed is higher than 30 km/h (20 mph) with 3rd gear held in Drive range for 2 seconds or more.
    • One driving cycle detection logic

Action Taken When the DTC Sets
    • DTC P0717 stores.
    • The malfunction indicator lamp (MIL) turns ON.

Diagnostic Aids

Inspect for the following conditions:

    • The Input/Turbine speed sensor
    • The PCM and related wiring

If DTC P0717 cannot duplicate, the information included in the Freeze Frame data may be useful in determining the vehicle operating conditions when the DTC set.

DTC Confirmation Procedure
  1. Turn the ignition switch to the LOCK position.
  2. Connect the scan tool to the data link connector (DLC).
  3. Turn the ignition switch ON.
  4. Use the scan tool in order to clear the following items:
    5. • DTC P0717
    • Any pending DTCs
  5. Start the engine.
  6. Warm the engine up to normal operating conditions.
  7. Turn O/D switch to the ON position.
  8. Operate the vehicle under all the following conditions:
    9. • Keep the vehicle speed approximately at or slightly above 10 km/h (7 mph) with 1st gear held in Drive range for 1 second or more.
    • Increase the vehicle speed to approximately 20 km/h (13 mph) with 2nd gear held in Drive range for 2 seconds or more.
    • Increase the vehicle speed to approximately 30 km/h (20 mph) with 3rd gear held in Drive range for 2 seconds or more.
  9. Stop the vehicle.
  10. Use the scan tool in order to test for a pending DTC.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame data on the scan tool if applicable. The scan tool creates an electronic copy of the data taken when the fault occurred. The information then stores in the scan tool for later reference.

    2.

  2. This step tests for input sensor resistance.

    3.

  3. This step checks for intermittents.

Step

Action

Value(s)

Yes

No

1

Was the On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 2.0L or Diagnostic System Check - Engine Controls in Engine Controls - 2.5L

2
  1. Install a scan tool.
  2. Turn the ignition to ON, leaving the engine OFF.
  3. Perform the scan tool Clear DTC Information function.
  4. Operate the vehicle within the Freeze Frame conditions as observed.

Does the scan tool display any other DTCs in addition to DTC P0717?

--

Go to the applicable DTC table

Go to Step 3

3

  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the PCM connector C3.
  3. Check the input speed sensor resistance.

Is the resistance within the specified range?

530-650  ohms

Go to Step 6

Go to Step 4

4

Inspect all of the electrical connections for poor terminal contact or a poor connection.

Does poor terminal contact or poor connections exist?

--

Go to Step 10

Go to Step  5

5

  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the input speed sensor connector.
  3. Check the input speed sensor resistance.

Is the resistance within the specified range?

530-650  ohms

Go to Step 6

Go to Step 11

6

  1. Install a known good PCM. Refer to Powertrain Control Module Replacement in Engine Controls-2.0L or Powertrain Control Module Replacement in Engine Controls-2.5L.
  2. Perform the DTC Confirmation Procedure.

Does DTC P0717 reset?

--

Go to Step 1

Go to Step 7

7

Visually check the sensor and overdrive clutch drum for damage or foreign material.

Is damage or foreign material present?

--

Step  10

Go to Step 8

8

Refer to Diagnostic Aids for a possible intermittent condition. If OK, replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls-2.0L or Powertrain Control Module Replacement in Engine Controls-2.5L.

Is the procedure complete?

--

Go to Step 9

--

9
  1. Turn the ignition switch to the LOCK position.
  2. Connect all the connectors.
  3. Perform the DTC Confirmation Procedure.

Does the scan tool display any DTCs?

--

Go to the applicable DTC table

System OK

10

Repair as necessary.

Is the system operating properly?

--

System OK

Step  2

11

Replace the input speed sensor.

Is the system operating properly?

--

System OK

Step  2