Roof Console Replacement Envoy XUV
Removal Procedure
- Open the sunglasses compartment cover or
the beauty cover on the console.
- Remove the 2 screws (1) that retain the console (2) to the roof
panel.
- Pull the console down to disengage clips.
- Disconnect the electrical connectors (3).
- Remove the console from the vehicle.
- If replacing the console, remove the switches. Refer to
Quarter Window Switch Replacement
in Body Rear End.
- If replacing the console, remove the garage door opener, if equipped.
Refer to
Garage Door Opener Replacement
in
Garage Door Opener.
- If replacing the console, remove the OnStar® microphone if, equipped.
Refer to
Mobile Telephone Microphone Replacement
in Cellular
Communication.
- If replacing the console, remove the noise cancellation microphone if,
equipped. Refer to
Radio Volume Compensator Interior Noise Microphone Replacement
in Entertainment.
- If replacing the console, remove the personal message player/recorder,
if equipped. Refer to
Personal Message Player/Recorder Replacement
in Entertainment.
Installation Procedure
- If replacing the console, install the personal message player/recorder,
if equipped. Refer to
Personal Message Player/Recorder Replacement
in Entertainment.
- If replacing the console, install the noise cancellation microphone,
if equipped. Refer to
Radio Volume Compensator Interior Noise Microphone Replacement
in Entertainment.
- If replacing the console, install the OnStar® microphone, if equipped.
Refer to
Mobile Telephone Microphone Replacement
in Cellular
Communication.
- If replacing the console, install the garage door opener, if equipped.
Refer to
Garage Door Opener Replacement
in
Garage Door Opener.
- If replacing the console, install the switches. Refer to
Quarter Window Switch Replacement
in Body Rear End.
- Connect the electrical connectors (3).
- Install the front retaining clips by pressing the console (2) into
the roof.
Notice: Refer to Fastener Notice in the Preface section.
- Install the 2 screws (1) retaining the console to the roof panel.
Tighten
Tighten the screws to 1.2 N·m (10 lb in).
- Close the sunglasses compartment cover on the console or snap the beauty
cover into place.
Roof Console Replacement Trailblazer, Envoy, Rainier
Removal Procedure
- Remove the dome lamp lenses by gently prying the lenses from the console.
- Remove the 2 screws that retain the console to the roof panel.
- Release the front retaining tabs.
- Lower the console and disconnect the electrical connectors as needed.
- Remove the console from the vehicle
- If replacing the console, remove the garage door opener if equipped. Refer to
Garage Door Opener Replacement
.
- If replacing the console, remove the OnStar® microphone if equipped. Refer to
Mobile Telephone Microphone Replacement
.
- If replacing the console, remove the personal message player/recorder if equipped. Refer to
Personal Message Player/Recorder Replacement
.
- If replacing the console, remove the power sunroof switch if equipped. Refer to
Sunroof Switch Replacement
.
- If replacing the console, remove the noise cancellation microphone if equipped. Refer to
Radio Volume Compensator Interior Noise Microphone Replacement
.
Installation Procedure
- If replacing the console, install the noise cancellation microphone if equipped. Refer to
Radio Volume Compensator Interior Noise Microphone Replacement
.
- If replacing the console, install the power sunroof switch if equipped. Refer to
Sunroof Switch Replacement
.
- If replacing the console, install the personal message player/recorder if equipped. Refer to
Personal Message Player/Recorder Replacement
.
- If replacing the console, install the OnStar® microphone if equipped. Refer to
Mobile Telephone Microphone Replacement
.
- If replacing the console, install the garage door opener if equipped. Refer to
Garage Door Opener Replacement
.
- Position the console to the roof panel.
- Connect the electrical connectors as needed.
- Seat the front retaining tabs.
Notice: Refer to Fastener Notice in the Preface section.
- Install the 2 screws retaining the console to the roof panel.
Tighten
Tighten the screws to 1.2 N·m (10 lb in).
- Install the dome lamp lenses.