The ignition 1 voltage circuit supplies 12 volts to the traction control switch. The EBCM turns OFF the traction off indicator by applying ground to the service traction control signal circuit.
The traction control system can be controlled by the operator in the following ways:
• | Through operation of the traction control switch. |
• | Through programming of the traction control system automatic engagement feature. |
Depending on the programmed state, the operation of the traction control system, as well as the operation of the traction off and low traction indicators, differs. For a more detailed explanation of these operational characteristics, refer to Traction Control Indicator Lamps in ABS Description and Operation .
Observe the data list parameters listed below in order to determine the status of the traction control system when it is unknown if the system is operational.
• | Traction Control Enabled |
• | Traction Off Lamp Command |
Press the traction control switch and observe the scan tool in order to verify a change in the status of the data list parameters.
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to Testing for Intermittent Conditions and Poor Connections , Wiring Repairs and Connector Repairs in Wiring Systems.
The numbers below refer to the step numbers on the diagnostic table.
This step simulates pressing and releasing a properly functioning traction control switch.
The traction control switch may be damaged if the traction control switch signal circuit is shorted to voltage.
This step tests if the ignition 1 voltage circuit can supply adequate power to the traction control switch.
This step tests if the EBCM is commanding the traction off indicator OFF.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Antilock Brake System Schematics | |||
1 | Did you perform the ABS Diagnostic System Check? | Go to Step 2 | |
2 |
Does the traction off indicator illuminate for 3 seconds and then turn OFF? | Go to Step 3 | Go to Step 7 |
3 | Press and release the traction control switch. Does the traction off indicator turn ON? | Go to Diagnostic Aids | Go to Step 4 |
4 |
Does the Traction Control Enabled status change? | Go to Step 13 | Go to Step 5 |
Important: Do not disconnect the traction control switch harness connector during this step.
Does the Traction Control Enabled status change? | Go to Step 12 | Go to Step 6 | |
Test the traction control switch signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 13 | |
Important: If the ignition is ON for more than 10 seconds, the EBCM sets DTC C0283.
Does the test lamp illuminate? | Go to Step 8 | Go to Step 14 | |
Does the traction off indicator illuminate? | Go to Step 13 | Go to Step 9 | |
9 | Test the service traction control signal circuit for a short to ground or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 10 |
10 | Test the ground circuit of the traction control switch for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 11 |
11 | Inspect for poor connections at the harness connector of the traction control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 12 |
12 | Replace the traction control switch. Refer to Electronic Traction Control Switch Replacement . Did you complete the replacement? | Go to Step 15 | -- |
13 |
Important: Following EBCM replacement, use the scan tool to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Did you complete the replacement? | Go to Step 15 | -- |
14 | Repair the high resistance in the ignition 1 voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 15 | -- |
15 | Press and release the traction control switch several times. Does the traction off indicator turn ON and OFF each time the switch is pressed? | System OK | Go to Step 2 |