GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

    Caution: Refer to Approved Equipment for Collision Repair Caution in the Preface section.

    Important: Before beginning the repair, refer to Metal Panel Bonding for proper adhesive applicator preparations and general information.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  3. Remove all related panels and components.
  4. Repair as much of the damage as possible to factory specifications. Refer to Dimensions - Body .
  5. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint/Coatings.
  6. Remove the door assembly. Refer to Rear Side Door Replacement in Doors.

  7. Object Number: 1335889  Size: SH
  8. Locate and drill out all factory welds. Note the number and location of welds at the upper window frame and the mirror locations.

  9. Object Number: 885546  Size: SH
  10. Grind the edges of the door outer panel to separate the outer door panel from the door shell.

  11. Object Number: 864445  Size: SH

    Caution: Inspection of the door guard beam for damage must be performed before replacement of the door outer panel. If damage to the door guard beam is found the door must be replaced. Failure to do so may compromise the structural integrity of the vehicle and may cause personal injury if the vehicle is involved in a collision.

  12. Remove the outer door panel.
  13. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint/Coatings.

  14. Object Number: 885547  Size: SH
  15. Straighten the edges of the door shell.

Installation Procedure


    Object Number: 885548  Size: SH
  1. Using a grinding disk, grind the surface of the door shell, mating the flanges to bare steel.

  2. Object Number: 885549  Size: SH
  3. Scuff the opposing mating surfaces of the door outer panel to remove the gloss of the E-Coat.

  4. Object Number: 1335889  Size: SH
  5. Drill 8 mm (5/16 in) plug weld holes, as necessary, in the locations noted from the original panel.
  6. Important: In any area damaged beyond recognition, space plug weld holes every 40 mm (1 in) apart.

  7. Clean the mating surfaces.

  8. Object Number: 885550  Size: SH

    Important: The adhesive has a 40-50 minute working time. Do not allow the door to totally cure off the vehicle, as proper alignment of the door outer panel to the door shell will be difficult.

  9. Apply a 3-6 mm (1/8-1/4 in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent, to both of the mating surfaces.
  10. Using a small acid brush, spread a coat of adhesive to cover all the bare metal surfaces to ensure corrosion protection.

  11. Object Number: 864496  Size: SH

    Important: Do NOT pull the panels apart after being joined together. Slide the panels against each other to realign the panels.

  12. Install the door outer panel to the door shell.
  13. Clamp the door outer panel into position as required.

  14. Object Number: 885552  Size: SH
  15. Using a hammer, re-hem the hem flanges around the door shell .
  16. Continue to hammer in stages along the hem flanges.

  17. Using lacquer thinner, remove the excess adhesive from the door panel area.
  18. Install the door to the vehicle. Inspect the door outer panel for proper alignment. Adjust the alignment as required.

  19. Object Number: 1335890  Size: SH
  20. Using metal-inert gas (MIG), weld the door outer panel to the door frame in the locations noted at the upper door frame.
  21. Clean and prepare all welded surfaces.

  22. Object Number: 885555  Size: SH
  23. Apply Fusor super flexible anti-flutter foam-fast set, Fusor P/N 121/124, or equivalent, in 4-5 evenly spaced locations between the door outer panel and the inner safety beam.
  24. Apply sealers and anti-corrosion materials to the repair area as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint/Coatings.
  25. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems in Paint/Coatings.
  26. Install the door assembly. Refer to Rear Side Door Replacement in Doors.
  27. Install all related panels and components.
  28. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  29. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.