Engine Mount Replacement - Right Side Four-Wheel Drive

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
3. Remove the engine protection shield. Refer to Engine Protection Shield Replacement .
4. Remove the shock module. Refer to Shock Absorber and Spring Assembly Replacement .
5. Remove the left side wheel drive shaft. Refer to Wheel Drive Shaft Replacement .
6. Remove the front differential carrier. Refer to Differential Carrier Assembly Replacement .



7. Remove the lower engine mount retaining nuts from the engine mount frame bracket.



8. Remove the 3 mounting bolts that secure the upper engine mount bracket to the engine block bracket.



9. Remove the 3 retaining bolts from the frame engine mount bracket.



10. Install a pole jack underneath the oil pan.
11. Insert a block of wood between the oil pan and the pole jack.



12. Raise the engine 2¼ inches measuring from the bottom of the oil pan to the front edge of the transmission support crossmember.
13. Shift the engine towards the left side of the frame.



14. Remove the engine mount frame bracket from the frame.



15. Remove the engine mount with the upper engine mount bracket as an assembly.
16. Separate the engine mount from the upper engine mount bracket.



17. Remove the engine mount bracket spacer if damaged.

Notice: Refer to Fastener Notice in the Preface section.




1. Install the engine mount bracket spacer if necessary.

Tighten
Tighten the spacer bolts to 50 N·m (37 lb ft).





Important: Verify that the cut out side of the engine mount shield is positioned away from the engine.

2. Install the engine mount to the upper engine mount bracket.

Tighten
Tighten the engine mount nuts to 50 N·m (37 lb ft).




3. Install the engine mount to engine.

Tighten
Tighten the engine mount bolts to 50 N·m (37 lb ft).

4. Install the engine mount frame bracket to the frame.
5. Install the engine mount frame bracket retaining bolts.

Tighten
Tighten the bolts to 100 N·m (74 lb ft).

6. Shift the engine back towards the right side of the frame.
7. Install the left side engine mount frame bracket.
8. Install the left side engine mount frame bracket retaining bolts.

Tighten
Tighten the bolts to 100 N·m (74 lb ft).




9. Lower the engine, aligning the engine mount studs with the holes in the frame bracket.
10. Remove the pole jack and block of wood.
11. Tighten the engine mount nuts.

Tighten
Tighten the nuts to 50 N·m (37 lb ft).

12. Install the shock module. Refer to Shock Absorber and Spring Assembly Replacement .
13. Install the front differential carrier. Refer to Differential Carrier Assembly Replacement .
14. Install the left side wheel drive shaft. Refer to Wheel Drive Shaft Replacement .
15. Install the engine protection shield. Refer to Engine Protection Shield Replacement .
16. Install the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
17. Lower the vehicle. Refer to Lifting and Jacking the Vehicle .

Engine Mount Replacement - Right Side Two-Wheel Drive

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
3. Remove the engine protection shield. Refer to Engine Protection Shield Replacement .
4. Remove the shock module. Refer to Shock Absorber and Spring Assembly Replacement .



5. Remove the lower engine mount retaining nuts from the engine mount frame bracket.



6. Remove the 3 mounting bolts that secure the upper engine mount bracket to the engine block bracket.



7. Remove the 3 bracket retaining bolts from the frame engine mount.



8. Install a pole jack underneath the oil pan.
9. Insert a block of wood between the oil pan and the pole jack.



10. Raise the engine 2¼ inches measuring from the bottom of the oil pan to the front edge of the transmission support crossmember.
11. Shift the engine towards the left side of the frame.



12. Remove the engine mount frame bracket from the frame.



13. Remove the engine mount with the upper engine mount bracket as an assembly.
14. Separate the engine mount from the upper engine mount bracket.



15. Remove the engine mount bracket spacer if damaged.

Notice: Refer to Fastener Notice in the Preface section.




1. Install the engine mount bracket spacer if it has been replaced.

Tighten
Tighten the bolts to 50 N·m (37 lb ft).





Important: Make sure that the cut out side of the engine mount shield is positioned away from the engine.

2. Install the engine mount to the upper engine mount bracket.

Tighten
Tighten the engine mount nuts to 50 N·m (37 lb ft).




3. Install the engine mount to engine.

Tighten
Tighten the engine mount bolts to 50 N·m (37 lb ft).

4. Install the engine mount frame bracket to the frame.
5. Install the engine mount frame bracket retaining bolts.

Tighten
Tighten the bolts to 100 N·m (74 lb ft).

6. Shift engine back to the right side of the frame.
7. Install the left side engine mount frame bracket.
8. Install the retaining bolts to the left side of the engine mount frame bracket.

Tighten
Tighten the bolts to 100 N·m (74 lb ft).




9. Lower the engine, aligning the engine mount studs with the holes in the frame bracket.
10. Remove the pole jack and the block of wood.
11. Tighten the engine mount nuts.

Tighten
Tighten the nuts to 50 N·m (37 lb ft).

12. Install the shock module. Refer to Shock Absorber and Spring Assembly Replacement .
13. Install the engine protection shield. Refer to Engine Protection Shield Replacement .
14. Install the front tire and wheels. Refer to Tire and Wheel Removal and Installation .
15. Lower the vehicle. Refer to Lifting and Jacking the Vehicle .