This repair procedure gives you the option of using an installation procedure for either metal-inert gas (MIG) welding or adhesive bonding. The choice of installation depends on the type of application requirements. The adhesive bonding procedure may also require MIG welding in some areas of the repair.

Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

Note: Before beginning the repair, refer to Metal Panel Bonding for proper adhesive preparations and general information.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
2. Disable the SIR system. Refer to SIR Disabling and Enabling.
3. Restore as much of the damage as possible to factory specifications. Refer to Dimensions - Body.
4. Remove all related panels and components.

Warning: Refer to Foam Sound Deadeners Warning in the Preface section.

5. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.



6. Locate and drill out all factory welds. Note the number and location of welds for installation of the lower quarter.



7. Remove the lower quarter panel.

1. Drill 8 mm (5/16 in) plug weld holes as necessary in locations noted from the original quarter panel.

Note: If the location of the original plug weld holes can not be determined, or if structural weld-thru adhesive is present, space the plug weld holes every 40 mm (1½ in) apart.

2. Prepare all mating surfaces as necessary.
3. Apply GM-approved Weld-Thru coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.



4. Position the lower quarter panel to the body.



5. Plug weld accordingly.
6. Clean and prepare all welded surfaces.
7. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
8. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems.
9. Install all related panels and components.
10. Enable the SIR system. Refer to SIR Disabling and Enabling.
11. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.

1. Grind the surface of the body mating flanges to bare steel.



2. Grind the lower quarter panel mating flanges to remove the E-coating. Take care not to damage the corners or thin the metal during the grinding operation.
3. Clean the mating surfaces.




Note: The adhesive has a 40-50 minute working time. Do not allow the adhesive to totally cure off the vehicle, as proper alignment of the lower quarter panel to the body will be difficult.

4. Apply a 3-6 mm (1/8 to 1/4 in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent to both of the mating surfaces.
5. Using a small acid brush, spread a coat of adhesive to cover all the bare metal surfaces to ensure corrosion protection.



6. Apply a 9-13 mm (3/8 to 1/2 in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent to the service part mating surfaces.




Note: DO NOT pull the panels apart after being joined together. Slide the panels against each other to realign the panels.

7. Install the lower quarter panel to the body.



8. Clamp the lower quarter panel into position as required.
9. Using lacquer thinner remove the excess adhesive from the lower quarter panel area.
10. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
11. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems.
12. Install all related panels and components.
13. Enable the SIR system. Refer to SIR Disabling and Enabling.
14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.