GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The Powertrain relay is a normally open relay. The relay armature is held in the open position by spring tension. Battery positive voltage is supplied directly to the relay coil and the armature contact at all times. The powertrain control module (PCM) supplies the ground path to the relay coil control circuit via an internal integrated circuit, called an output driver module (ODM). One of the ODM output circuits is configured to operate as a low side driver for the main relay. The low side driver also incorporates a fault detection circuit, which is continuously monitored by the PCM. When the PCM commands the relay ON, the expected voltage on the relay coil control circuit should be a low voltage condition. If the fault detection circuit measures a high voltage condition, DTC P0685 will set. DTC P0685 indicates a short to battery positive voltage, or ignition 1 voltage on the powertrain relay control circuit.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0685 Engine Controls Ignition Relay Control Circuit

Conditions for Running the DTC

    • The battery voltage is between 11-18 volts.
    •  The ignition is ON.
    • The diagnostic runs continuously when the above conditions are met.

Conditions for Setting the DTC

The PCM detects more than 4.6 volts on the relay coil control circuit for more than 2 seconds.

Action Taken When the DTC Sets

    • The PCM will not illuminate the malfunction indicator lamp (MIL) if this diagnostic runs and fails.
    • The engine will crank, but will not run.
    • The Class 2 communications will be available with the use of a scan tool.

Conditions for Clearing the DTC

    • A current DTC Last Test Failed clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
    • Clear the DTC with a scan tool.

Diagnostic Aids

The DTC P0685 diagnostic table assumes that the vehicle battery is fully charged. Refer to Battery Inspection/Test in Engine Electrical.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics and Power Distribution Schematics in Wiring Systems

Connector End View Reference: Engine Controls Connector End Views and Electrical Center Identification Views in Wiring Systems

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

Is DTC P0685 active?

--

Go to Step 3

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

  1. Turn OFF the ignition.
  2. Remove the powertrain relay from the underhood junction block with the J 43244 Relay Puller Pliers. Refer to Relay Replacement in Wiring Systems.
  3. Notice: Refer to Test Probe Notice in the Preface section.

  4. Probe the powertrain relay control circuit terminal at the underhood junction block with a test lamp that is connected to a good ground. Refer to Troubleshooting with a Test Lamp in Wiring Systems.

Does the test lamp illuminate?

--

Go to Step 7

Go to Step 4

4

  1. Turn ON the ignition, with the engine OFF.
  2. Probe the powertrain relay coil control circuit at the underhood junction block with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

--

Go to Step 5

Go to Step 9

5

  1. Turn OFF the ignition.
  2. Disconnect the powertrain control module (PCM) electrical connector that contains the relay control circuit from the PCM. Refer to Powertrain Control Module Replacement .
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the powertrain relay control circuit terminal at the underhood junction block with a test lamp that is connected to a good ground. Refer to Probing Electrical Connectors in Wiring Systems.

Does the test lamp illuminate?

--

Go to Step 6

Go to Step 12

6

  1. Turn OFF the ignition.
  2. Disconnect the negative battery cable at the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  3. Disconnect the underhood junction block electrical connector that contains the powertrain relay coil control circuit. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.
  4. Disconnect the powertrain relay control circuit wire terminal from the underhood junction block electrical connector.
  5. Connect the electrical connector that contained the powertrain relay coil control circuit to the underhood junction block.
  6. Connect the negative battery cable at the battery.
  7. Turn ON the ignition, with the engine OFF.
  8. Probe the powertrain relay control circuit wire terminal at the PCM electrical connector with a test lamp that is connected to a good ground. Refer to Probing Electrical Connectors in Wiring Systems.

Does the test lamp illuminate?

--

Go to Step 13

Go to Step 15

7

  1. Turn OFF the ignition.
  2. Disconnect the PCM electrical connector that contains the relay control circuit from the PCM. Refer to Powertrain Control Module Replacement .
  3. Probe the relay coil control circuit terminal at the underhood junction block with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

--

Go to Step 8

Go to Step 12

8

  1. Turn OFF the ignition.
  2. Disconnect the negative battery cable at the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  3. Disconnect the underhood junction block electrical connector that contains the powertrain relay control circuit. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.
  4. Connect the negative battery cable at the battery.
  5. Probe the powertrain relay control circuit wire terminal at the underhood junction block electrical connector with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

--

Go to Step 13

Go to Step 15

9

Measure the resistance from terminal 30 of the relay to terminal 85 with a DMM. Refer to Troubleshooting with a Test Lamp in Wiring Systems.

Does the DMM display the specified value?

∞ ohms

Go to Step 10

Go to Step 14

10

Measure the resistance from terminal 85 of the relay to terminal 87 with a DMM.

Does the DMM display the specified value?

∞ ohms

Go to Step 11

Go to Step 14

11

Measure the resistance from terminal 85 of the relay to terminal 86 with a DMM.

Does the DMM display the specified value?

70-110 ohms

Go to Step 17

Go to Step 14

12

Test for shorted terminals and poor connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 16

13

Repair the short to voltage in the powertrain relay control circuit between the underhood junction block electrical connector and the PCM electrical connector. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 17

--

14

Replace the powertrain relay. Refer to Relay Replacement in Wiring Systems.

Did you complete the replacement?

--

Go to Step 17

--

15

Replace the underhood junction block. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.

Did you complete the replacement?

--

Go to Step 17

--

16

Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 17

--

17

  1. Reassemble the vehicle as necessary.
  2. Replace any open fuses.
  3. Turn OFF the ignition for 30 seconds.
  4. Attempt to start the engine.

Does the engine start and run?

--

Go to Step 18

Go to Engine Cranks but Does Not Run

18

  1. Clear the DTCs with a scan tool.
  2. Operate the vehicle for 5 minutes.

Does the DTC set during this ignition cycle?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK