Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3948: Left Front Turn Signal CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Left Front Turn Signal Control | B3948 | B3948 | 1 | -- |
Right Front Turn Signal Control | B3949 | B3949 | 1 | -- |
Left Rear Stop/Turn Lamp Control | B3950 | B3950 | 1 | -- |
Right Rear Stop/Turn Lamp Control | B3951 | B3951 | 1 | -- |
Left Turn Signal Switch Signal | 1 | 1 | 1 | -- |
Right Turn Signal Switch Signal | 1 | 1 | 1 | -- |
Turn Signal/Multifunction Switch Ground | -- | 1 | -- | -- |
LF Park/Turn Signal Lamp Ground | -- | 1 | -- | -- |
RF Park/Turn Signal Lamp Ground | -- | 1 | -- | -- |
Left Tail/Stop and Turn Signal Lamp Ground | -- | 1 | -- | -- |
Right Tail/Stop and Turn Signal Lamp Ground | -- | 1 | -- | -- |
1. Park, License, and/or Tail Lamps Malfunction | ||||
Circuit/System Description
Ground is applied at all times at G200 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to the front and rear turn signal lamps through there respective voltage supply circuits. When a turn signal request is received by the BCM, a serial data message is sent to the instrument panel cluster (IPC) requesting the respective turn signal indicator be pulsed ON and OFF.
Conditions for Running the DTC
Battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
DTC B3948 will set when the BCM detects a short to ground or an open/high resistance in the LF turn signal control circuit.
Action Taken When the DTC Sets
| • | When the DTC is present, the LF turn signal will not operate. |
| • | The left turn signal indicator located on the instrument panel cluster (IPC) will flash rapidly. |
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the left front turn signal lamp.
- Ignition OFF, exterior lamps OFF, test for less than 5.0 ohms between the ground circuit terminal 3 and ground.
- Connect a test lamp between the control circuit terminal 1 and ground.
- Command the left front Turn Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the left front turn signal lamp assembly.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
