GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Uplander Ext. 🢒 Steering 🢒 Power Steering 🢒 Power Steering Cooler Pipe/Hose Replacement

Removal Procedure
  1. Turn the steering wheel to the straight forward position, support it from movement, and remove the key from the ignition.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  3. Remove the right side engine splash shield. Refer to Engine Splash Shield Replacement.
  4. Place the drain pan under the vehicle.

    5. Object Number: 1831711 Size: SH
  5. Remove the 2 routing clip retainers from the RH side of the front cradle.

    6. Object Number: 1831670 Size: SH
  6. Remove the 2 routing clip retainers from the front side of the front cradle.

    7. Object Number: 1831719 Size: SH
  7. Compress the clamp (1) and disconnect the power steering inlet pipe/hose (2) from the cooler pipe (3).

    8. Object Number: 1831763 Size: SH

    Warning: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage may cause loss of steering control which could result in an accident and possible personal injury.

  8. Remove the intermediate shaft pinch bolt and separate the intermediate shaft from the steering gear.
  9. Place a jack stand at the rear of the cradle support.
  10. Remove the 2 rear cradle support bolts.
  11. Using the jack stand, lower the rear of the cradle support for clearance.

    12. Object Number: 1831765 Size: SH
  12. Remove the 2 power steering gear heat shield bolts and the shield.

    13. Object Number: 1831758 Size: SH
  13. Disconnect the cooler pipe/hose fitting from the steering gear. Discard the O-ring seal.
  14. Remove the cooler pipe/hose from the vehicle.

Installation Procedure
  1. Position the cooler pipe/hose to the vehicle.

    2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1831758 Size: SH
  2. Using a new O-ring seal, connect the cooler pipe/hose fitting to the steering gear and tighten to 27 N·m (20 lb ft).

    3. Object Number: 1831765 Size: SH
  3. Position the steering gear heat shield, install the 2 bolts, and tighten to 14 N·m (124 lb in).

    4. Object Number: 1831719 Size: SH
  4. Compress the clamp (1) and connect the power steering pump inlet pipe/hose (2) to the power steering cooler pipe/hose (3).
  5. Remove the drain pan from under the vehicle.
  6. Using the jack stand, raise the rear of the cradle support.
  7. Install the 2 rear cradle support bolts and tighten to 165 N·m (122 lb ft).
  8. Remove the jack stand.

    9. Object Number: 1831763 Size: SH
  9. Position the intermediate shaft to the steering gear, install the pinch bolt and tighten to 48 N·m (35 lb ft).

    10. Object Number: 1831711 Size: SH
  10. Install the 2 routing clip retainers to the RH side of the cradle support.
  11. Install the right side engine splash shield. Refer to Engine Splash Shield Replacement.

    12. Object Number: 1831670 Size: SH
  12. Install the 2 routing clip retainers to the front side of the cradle support.
  13. Lower the vehicle.
  14. Fill and bleed the power steering system. Refer to Power Steering System Bleeding.