Emblem/Nameplate Repair Chevrolet

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate perform the following:

1.1.	Use tape to protect the body panel during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.

2. To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070 .
3. Apply heat using a circular motion for about 30 seconds holding the J 25070 approximately 152 mm (6 in) from the surface.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
5. When replacing, remove all adhesive as follows:

•	For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.

•	For plastic panels use a lint free cloth and varnish makers and painters (VMP) naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and VMP naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.
3. If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown below.



4. For the UPLANDER (5) emblem/nameplate, install as shown.

•	For the LS or LT emblem/nameplate, dimension (a) is 270 mm (10.63 in) from the left edge of the liftgate to the left edge of the LS or LT emblem/nameplate.

•	Dimension (b) is 31 mm (1.30 in) from the outer edge of the liftgate to the left side of the UPLANDER emblem/nameplate edge.

•	Dimension (c) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom of the UPLANDER emblem/nameplate.

•	For the Chevrolet (2) emblem/nameplate, dimension (d) is 31 mm (1.30 in) from the right edge of the liftgate to the right edge of the Chevrolet emblem/nameplate.

•	For the VERSATRAK (3) emblem/nameplate, dimension (e) is 53 mm (2.09 in) from the bottom edge of the liftgate to the bottom edge of the VERSATRAK (3) emblem/nameplate.

•	Dimension (f) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom edge of the Chevrolet (2) emblem/nameplate.

•	Dimension (g) is 37 mm (1.46 in) from the right edge of the liftgate to the right edge of the VERSATRAK emblem/nameplate.

5. The Chevrolet (1) emblem is centered and indexed above the license plate pocket of the liftgate.
6. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
7. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

Important: Do not touch the adhesive backing on the emblem/nameplate.

8. Remove the protective liner from the back of the emblem/nameplate.
9. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
10. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
11. Remove the protective tape from the body panel.

Emblem/Nameplate Repair Buick

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate perform the following:

1.1.	Use tape to protect the body panel during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.

2. To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070 .
3. Apply heat using a circular motion for about 30 seconds holding the J 25070 approximately 152 mm (6 in) from the surface.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
5. When replacing, remove all adhesive as follows:

•	For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.

•	For plastic panels use a lint free cloth and varnish makers and painters (VMP) naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and VMP naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.
3. If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown below.



4. For the TERRAZA (3) emblem/nameplate, install as shown.

•	Dimension (a) is 31 mm (1.30 in) from the outer edge of the liftgate to the left side of the TERRAZA (4) emblem/nameplate edge.

•	Dimension (b) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom of the TERRAZA (4) emblem/nameplate.

•	For the CXL emblem/nameplate, dimension (c) is 31 mm (1.30 in) from the right edge of the liftgate to the edge of the CXL (2) emblem/nameplate.

•	Dimension (d) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom edge of the CXL (2) emblem/nameplate.

•	Dimension (e) is 37 mm (1.46 in) from the right edge of the liftgate to the right edge of the VERSATRAK (3) emblem/nameplate.

•	Dimension (f) is 53 mm (2.09 in) from the bottom edge of the liftgate to the bottom edge of the VERSATRAK (3) emblem/nameplate.

5. The Buick (1) emblem is centered and indexed above the license plate pocket of the liftgate.
6. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
7. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

Important: Do not touch the adhesive backing on the emblem/nameplate.

8. Remove the protective liner from the back of the emblem/nameplate.
9. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
10. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
11. Remove the protective tape from the body panel.

Emblem/Nameplate Repair Pontiac

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate perform the following:

1.1.	Use tape to protect the body panel during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.

2. To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070 .
3. Apply heat using a circular motion for about 30 seconds holding the J 25070 approximately 152 mm (6 in) from the surface.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
5. When replacing, remove all adhesive as follows:

•	For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.

•	For plastic panels use a lint free cloth and varnish makers and painters (VMP) naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and VMP naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.
3. If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown below.



4. For the Montana SV6 (4) emblem/nameplate, install as shown.

•	Dimension (a) is 31 mm (1.30 in) from the left outer edge of the liftgate to the left side of the Montana SV6 emblem/nameplate edge.

•	Dimension (b) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom of the Montana SV6 emblem/nameplate.

•	For the Pontiac (2) emblem/nameplate, dimension (c) is 31 mm (1.30 in) from the right edge of the liftgate to the right edge of the Pontiac emblem/nameplate.

•	Dimension (d) is 209 mm (8.23 in) from the bottom edge of the liftgate to the bottom edge of the Pontiac emblem/nameplate.

•	For the VERSATRAK (3) emblem/nameplate, dimension (e) is 37 mm (1.46 in) from the right edge of the liftgate to the right edge of the VERSATRAK emblem/nameplate.

•	Dimension (f) is 53 mm (2.09 in) from the bottom edge of the liftgate to the bottom edge of the VERSATRAK emblem/nameplate.

5. The Pontiac (1) emblem/nameplate is centered and indexed above the license plate pocket of the liftgate.
6. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
7. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

Important: Do not touch the adhesive backing on the emblem/nameplate.

8. Remove the protective liner from the back of the emblem/nameplate.
9. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
10. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
11. Remove the protective tape from the body panel.