Circuit Description
The intake air temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The powertrain control module (PCM) applies 5 volts through a pull-up resistor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high signal voltage on the IAT sensor signal circuit. As the intake air warms, the sensor resistance becomes lower causing the PCM to monitor a lower voltage. If the PCM detects an excessively low IAT sensor signal voltage, high temperature indicated, DTC P0112 will set.
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0117, P0118, P0125, P0128, P0502, P0503, P1114, or P1115 are not set. |
| • | The engine has been running for more than 10 seconds. |
| • | The vehicle speed is more than 40 km/h (25 mph). |
Conditions for Setting the DTC
| • | The IAT signal voltage indicates an intake air temperature that is more than 135°C (275°F). |
| • | The above conditions are present for at least 20 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
If DTC P0112 can be repeated only by duplicating the Failure Records conditions, refer to the Temperature vs Resistance table. The table may be used in order to test the IAT sensor at various temperatures, in order to evaluate the possibility of a shifted sensor that may be shorted above or below a certain temperature.
Test Description
The number below refer to the step number on the diagnostic table.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls ? | -- | Go to Step 2 | |
Does the scan tool indicate the IAT parameter is more than specified value? | 135°C (275°F) | Go to Step 4 | Go to Step 3 | |
3 |
Does scan tool indicate DTC P0112 failed this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions |
4 |
Does the scan tool indicate the IAT parameter is less than the specified value? | -37°C (-35°F) | Go to Step 6 | Go to Step 5 |
5 |
Did you find and correct the condition? | -- | Go to Step 8 | Go to Step 7 |
6 | Replace the IAT sensor. Refer to Intake Air Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 8 | -- |
7 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 8 | -- |
8 |
Does the DTC run and pass? | -- | Go to Step 9 | Go to Step 2 |
9 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
