GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Venture Ext. 🢒 Engine 🢒 Engine Mechanical - 3.4L 🢒 Power Steering Pressure Pipe/Hose Replacement

Removal Procedure
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

    2. Caution: Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.

    Notice: When adding fluid or making a complete fluid change, always use the proper power steering fluid. Failure to use the proper fluid will cause hose and seal damage and fluid leaks.

  2. Remove the intermediate shaft from the steering gear. Refer to Intermediate Steering Shaft Replacement in Steering Wheel and Column.
  3. Use a utility stand in order to support the frame rear.
  4. Remove the frame rear bolts. Refer to Front Frame Replacement in Frame and Underbody.
  5. Use the utility stand in order to lower the frame rear to gain access.
  6. Place the drain pan under the power steering pump and the power steering gear.

    7. Object Number: 417973 Size: SH
  7. Remove the power steering gear hose clip.
  8. Remove the inlet hose from the steering gear.
  9. Use the utility stand in order to raise the frame rear.
  10. Install the OLD frame bolts. Fully seat the frame bolts. Do NOT tighten the frame bolts.
  11. Lower the vehicle.
  12. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-3.4L.

    13. Object Number: 417974 Size: SH
  13. Remove the inlet hose from the pump.
  14. Remove the inlet hose from the hose retainer.
  15. Remove the inlet hose.

Installation Procedure
  1. Install the inlet hose.

    2. Object Number: 417974 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the inlet hose to the pump.

    3. Tighten
    Tighten the power steering gear inlet hose fitting to 27 N·m (20 lb ft).

  3. Install the inlet hose to the hose retainer.
  4. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-3.4L.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  6. Use a utility stand in order to support the frame rear.
  7. Remove and DISCARD the frame rear bolts.
  8. Use the utility stand in order to lower the frame rear to gain access.

    9. Object Number: 417973 Size: SH
  9. Install the inlet hose to the steering gear.

    10. Tighten
    Tighten the power steering gear inlet hose fitting to 27 N·m (20 lb ft).

  10. Install the power steering gear hose clip.
  11. Use the utility stand in order to raise the frame rear.
  12. Install the NEW frame rear bolts. Refer to Front Frame Replacement in Frame and Underbody.
  13. Install the intermediate shaft to the steering gear. Refer to Intermediate Steering Shaft Replacement in Steering Wheel and Column.
  14. Lower the vehicle.
  15. Fill the power steering fluid reservoir. Refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.
  16. Bleed the power steering system. Refer to Power Steering System Bleeding .