Diagnostic Aids
Before performing this procedure, ensure that the following conditions are met:
| • | The vehicle park brake is SET. |
| • | The rear parking assist (RPA) disable switch is ON. |
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Rear Parking Assist Schematics | ||||
1 | Did you review the operation and perform the necessary inspections? | -- | Go to Step 2 | |
2 |
Do all of the three display indicators illuminate for 2 seconds and then turn off? | -- | Go to Step 3 | Go to Step 4 |
3 |
Do all three display indicators illuminate for 2 seconds and then turn off? | -- | Go to Step 14 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
4 | Does the red indicator flash? | -- | Go to Rear Parking Assist Inoperative - Red Indicator Flashes | Go to Step 5 |
5 | Do all of the indicators but one indicator illuminate? | -- | Go to Step 7 | Go to Step 6 |
6 | Does any indicator remain on? | -- | Go to Step 8 | Go to Step 11 |
7 | Connect a test lamp between the control circuit of the inoperative indicator at the module connector and a good ground. Does the test lamp illuminate? | -- | Go to Step 21 | Go to Step 9 |
8 |
Does the test lamp illuminate? | -- | Go to Step 10 | Go to Step 20 |
9 | Test the control circuit of the inoperative indicator for an open, a short to battery voltage or for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 20 |
10 | Test the control circuit of the inoperative indicator for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 21 |
11 | Test the rear object sensor control module ground circuit for an open. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 12 |
12 | Test the rear object sensor control module ignition 1 voltage circuit for an open and for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 13 |
13 | Test the backup lamp supply voltage circuit for an open or for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 16 |
14 |
Do all of the three display indicators illuminate for 2 seconds and then turn off? | -- | Go to Step 15 | Go to Step 22 |
15 | Test the RPA switch signal circuit for an open or for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 21 |
16 |
Do all of the three display indicators illuminate for 2 seconds and then turn off? | -- | Go to Step 22 | Go to Step 17 |
17 | Test the RPA switch signal circuit for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 18 |
18 |
Does the test lamp illuminate? | -- | Go to Step 20 | Go to Step 19 |
19 | Test the rear parking assist display supply voltage circuit for an open and for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 21 |
20 | Inspect for poor connections at the harness connector of the rear parking assist display. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 24 |
21 | Inspect for poor connections at the harness connector of the rear object sensor control module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 25 |
22 | Inspect for poor connections at the harness connector of the RPA switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 26 | Go to Step 23 |
23 | Replace the RPA switch. Refer to Interior Lamp and Multifunction Switch Replacement in Doors. Did you complete the replacement? | -- | Go to Step 26 | -- |
24 | Replace the rear parking assist display. Refer to Information Center Telltale Assembly Replacement . Did you complete the replacement? | -- | Go to Step 26 | -- |
25 | Replace the rear object sensor control module. Refer to Object Alarm Module Replacement . Did you complete the replacement? | -- | Go to Step 26 | -- |
26 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
