GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 36797-A Getrag Axle Output Shaft Seal Installer
    • J 44755 Holding Fixture

Removal Procedure


    Object Number: 630581  Size: SH
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the extension housing vent hose (2) and clamp. Refer to Vent Hose Assembly Replacement .
  3. Remove the propeller shaft. Refer to Propeller Shaft Replacement in Propeller Shaft.

  4. Object Number: 630583  Size: SH
  5. Place a container under the extension housing.
  6. Remove the lubricant drain plug (1) and gasket. Allow the oil to drain.

  7. Object Number: 630584  Size: SH
  8. Remove the bolts (3), extension housing assembly (1), and shim (2) from the transfer case.
  9. Reference mark the shim for proper reassembly.


    Object Number: 754966  Size: SH
  10. If reusing the drivenshaft bearings, measure in both directions, the rotating torque of the drivenshaft and record the value for assembly.
  11. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 746838  Size: SH
  12. Install the extension housing assembly (3) to the J 44755 (2) with M8 x 1.25 bolts.
  13. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 630580  Size: SH
  14. Remove the flange nut (1).
  15. Remove the bolts and the extension housing assembly from the J 44755 .

  16. Object Number: 630586  Size: SH
  17. Position the extension housing assembly into a press.
  18. Press the pinion shaft from the flange.
  19. Remove and discard the extension housing seal.

Installation Procedure


    Object Number: 1486595  Size: SH
  1. Install the drive pinion (3) and NEW spacer (1) into the extension housing (2).

  2. Object Number: 659152  Size: SH
  3. Use the J 5590  (1) and a hydraulic press in order to install the bearing onto the shaft.

  4. Object Number: 746877  Size: SH
  5. Use the J 36797-A in order to install a new oil seal (2) into the extension housing.

  6. Object Number: 659154  Size: SH
  7. Position the flange and the extension housing assembly into a press.
  8. Lightly lubricate the splines on the driven shaft.
  9. Press the flange (1) onto the driven shaft.
  10. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 746838  Size: SH
  11. Install the extension housing assembly to the J 44755  (2) using M8 x 1.25 bolts (1).
  12. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 630580  Size: SH
  13. Install the flange nut (1) onto the driven shaft.
  14. Tighten
    Tighten the flange nut to 200 N·m (148 lb ft).

  15. Remove the extension housing assembly from the J 44755 .

  16. Object Number: 754966  Size: SH
  17. Measure the rotating torque of the driven shaft in both directions.
  18. When reusing drivenshaft bearings, the rotating torque should equal the value recorded during disassembly.
  19. Tighten
    A properly assembled shaft and NEW bearings should have a rotating torque of 1.5 N·m (13 lb in).

  20. Reinstall J 44755 to tighten the flange nut as required to achieve the proper rotating torque value. Do NOT loosen the flange nut to achieve the proper torque or a NEW spacer must be installed.

  21. Object Number: 630584  Size: SH
  22. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to both sides of the shim.
  23. Align the reference marks and install the shim (2) to the transfer case.
  24. Install the extension housing (1) and bolts (3) to the shim and transfer case.
  25. Tighten
    Tighten the extension housing bolts to 32 N·m (24 lb ft).


    Object Number: 630583  Size: SH
  26. Install the extension housing drain plug (1) and gasket to the extension housing.
  27. Tighten
    Tighten the plug to 32 N·m (24 lb in).

  28. Remove the extension housing fill plug (2) and gasket.
  29. Fill the extension housing with gear oil. Refer to Transfer Case Fluid Replacement .
  30. Install the extension housing fill plug and gasket.
  31. Tighten
    Tighten the plug to 28 N·m (21 lb in).


    Object Number: 630581  Size: SH
  32. Install the vent hose (2) and clamp (1). Refer to Vent Hose Assembly Replacement .
  33. Install the propeller shaft. Refer to Propeller Shaft Replacement in Propeller Shaft.
  34. Lower the vehicle.