GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2005 🢒 Venture Ext. 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 Fuel Injector Balance Test with Special Tool
Table 1: Fuel Injector Balance Test Example (Actual Results May Vary)

Object Number: 17713 Size: SF
(1)First Fuel Pressure Gage Reading
(2)Second Fuel Pressure Gage Reading

System Description

The scan tool is first used to energize the fuel pump relay. The fuel injector tester is then used to pulse each injector for a precise amount of time allowing a measured amount of fuel into the manifold. This causes a drop in system fuel pressure that can be recorded and used to compare each injector.

Fuel Injector Balance Test Example (Actual Results May Vary)

Cylinder

1

2

3

4

1st Reading

379 kPa (55 psi)

379 kPa (55 psi)

379 kPa (55 psi)

379 kPa (55 psi)

2nd Reading

280 kPa (41 psi)

310 kPa (45 psi)

340 kPa (49 psi)

317 kPa (46 psi)

Amount of Drop

99 kPa (14 psi)

69 kPa (10 psi)

39 kPa (6 psi)

62 kPa (9 psi)

Average Range: 47-87 kPa (6.8-12.6 psi)

Replace fuel injector - too much fuel pressure drop

Injector OK

Replace fuel injector - too little fuel pressure drop

Injector OK

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The engine coolant temperature (ECT) must be below the operating temperature in order to avoid irregular fuel pressure readings due to hot soak fuel boiling.

    2.

  2. If the pressure drop value for each fuel injector is within 20 kPa (3 psi) of the average pressure drop value, the fuel injectors are flowing properly.

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Did you perform the Fuel Injector Coil Test?

--

Go to Step 3

Go to Fuel Injector Solenoid Coil Test

3

Important : DO NOT perform this test if the engine coolant temperature (ECT) is above 94°C (201°F).

Observe the ECT parameter with a scan tool.

Does the scan tool indicate that the ECT parameter is less than the specified value?

94°C (201°F)

Go to Step 4

--

4

Important: Verify there is adequate fuel in the fuel tank before proceeding with this diagnostic.

  1. Turn OFF the ignition.
  2. Install the J 34730-1A Fuel Pressure Gage and the fuel pressure gage fitting. Refer to Fuel Pressure Gage Installation and Removal .
  3. Turn ON the ignition, with the engine OFF.
  4. Command the fuel pump ON with a scan tool.

    5. Important: 

       • You may need to command the fuel pump ON a few times, in order to obtain the highest possible fuel pressure.
       • Do not start the engine.

  5. Observe the J 34730-1A , with the fuel pump commanded ON.

Is the fuel pressure within the specified range?

358-405 kPa (52-59 psi)

Go to Step 5

Go to Fuel System Diagnosis

5

Important: The fuel pressure may vary slightly when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.

Monitor the J 34730-1A for 1 minute.

Does the fuel pressure drop more than the specified value?

34 kPa (5 psi)

Go to Fuel System Diagnosis

Go to Step 6

6

  1. Connect the J 39021 Fuel Injector Coil/Balance Tester, J 39021-210 Injector Test Adapter Box, and J 39021-410 Fuel Injector Test Harness to the fuel injector multi-way connector.
  2. Set the amperage supply selector switch on the fuel injector tester to the Balance Test 0.5-2.5 amp position.
  3. Command the fuel pump ON and then OFF with a scan tool.
  4. Record the fuel pressure indicated by the J 34730-1A after the fuel pressure stabilizes. This is the first pressure reading.

    5. Important: Record the fuel pressure value immediately after the fuel injector stops pulsing. The fuel pressure may rise after the fuel injector stops pulsing. Do not record the higher fuel pressure value.

  5. Energize the fuel injector by depressing the Push to Start Test button on the fuel injector tester.
  6. Record the fuel pressure indicated by the J 34730-1A . This is the second fuel pressure reading.
  7. Repeat steps 1 through 6 for each fuel injector.
  8. Subtract the second pressure reading from the first pressure reading for one fuel injector. The result is the pressure drop value.
  9. Obtain a pressure drop value for each fuel injector.
  10. Add all of the individual pressure drop values. This is the total pressure drop.
  11. Divide the total pressure drop by the number of fuel injectors. This is the average pressure drop.

Does any fuel injector have a pressure drop value that is more than the average pressure drop or less than the average pressure drop by the specified value?

20 kPa (3 psi)

Go to Step 7

Go to Symptoms - Engine Controls

7

Clean the fuel injectors. Refer to Fuel Injector Cleaning .

Did you complete the action?

--

Go to Step 8

--

8

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK