GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2005 🢒 Venture Ext. 🢒 Body 🢒 Instrument Panel, Gages, and Console 🢒 Instrument Panel Assembly Replacement

Removal Procedure
  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Remove the right closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side .
  3. Remove the left closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  4. Remove the knee bolster. Refer to Knee Bolster Replacement .
  5. Remove the instrument panel (I/P) accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
  6. Remove the I/P compartment. Refer to Instrument Panel Compartment Replacement .
  7. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
  8. Remove the inflatable restraint I/P module. Refer to Inflatable Restraint Instrument Panel Module Replacement in SIR.
  9. Remove the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.
  10. Remove the instrument panel cluster (IPC). Refer to Instrument Cluster Replacement .
  11. Remove the steering column. Refer to Steering Column Replacement in Steering Wheel and Column.
  12. Remove the hood release handle. Refer to Hood Primary Latch Release Cable Handle Replacement in Body Front End.
  13. Remove the front floor console. Refer to Front Floor Console Replacement .
  14. Remove the front floor console bracket. Refer to Floor Console Bracket Replacement .
  15. Remove the audio system. Refer to Radio Replacement in Entertainment.
  16. Remove the heater A/C controls. Refer to HVAC Control Module Replacement in HVAC Systems - Manual.
  17. Remove the switch bank. Refer to Instrument Panel Multifunction Switch Assembly Replacement in Lighting Systems.
  18. Remove the windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
  19. Remove the I/P upper trim. Refer to Instrument Panel Upper Trim Pad Replacement .
  20. Remove the headlamp switch. Refer to Headlamp Switch Replacement in Lighting Systems.
  21. Remove the data link connector. Refer to Data Link Connector Replacement in Computing/Integrating Systems.

    22. Object Number: 318207 Size: LH
  22. Remove the bolts/screws (1) that secure the instrument panel (3) to the body.
  23. Lift up from the bottom of the I/P in order to release the top retainers.
  24. Remove the I/P wiring harness. Refer to Instrument Panel Wiring Harness Replacement .
  25. Remove the instrument panel (3).

Installation Procedure

    Object Number: 318207 Size: LH

    Important: The instrument panel (I/P) will rest off of the lower mounts when you lower the I/P. This will aid in the routing of the wiring harness. Prop the I/P up in order to route the harness, as needed.

  1. Perform the following steps in order to install the instrument panel (2) to the body:
    2. 1.1. Secure the top retainers.
    1.2. Lower the instrument panel (I/P).
  2. Install the I/P wiring harness. Refer to Instrument Panel Wiring Harness Replacement .

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the bolts/screws (1) to the I/P body (3).

    4. Tighten
    Tighten the bolts/screws to 10 N·m (89 lb in).

  4. Install the data link connector. Refer to Data Link Connector Replacement in Computing/Integrating Systems.
  5. Install the headlamp switch. Refer Headlamp Switch Replacement in Lighting Systems.
  6. Install the I/P upper trim. Refer to Instrument Panel Upper Trim Pad Replacement .
  7. Install the windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
  8. Install the switch bank. Refer to Instrument Panel Multifunction Switch Assembly Replacement in Lighting Systems.
  9. Install the heater A/C controls. Refer to HVAC Control Module Replacement in HVAC Systems - Manual.
  10. Install the audio system. Refer to Radio Replacement in Entertainment.
  11. Install the front floor console bracket. Refer to Floor Console Bracket Replacement .
  12. Install the front floor console. Refer to Front Floor Console Replacement .
  13. Install the hood release handle. Refer to Hood Primary Latch Release Cable Handle Replacement in Body Front End.
  14. Install the steering column. Refer to Steering Column Replacement in Steering Wheel and Column.
  15. Install the IPC. Refer to Instrument Cluster Replacement .
  16. Install the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems.
  17. Install the inflatable restraint I/P module. Refer to Inflatable Restraint Instrument Panel Module Replacement in SIR.
  18. Install the I/P compartment. Refer to Instrument Panel Compartment Replacement .
  19. Install the I/P accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
  20. Install the knee bolster. Refer to Knee Bolster Replacement .
  21. Install the left closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  22. Install the right closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side .
  23. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  24. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.