Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Sliding Door Schematics Connector End View Reference: Power Door Systems Connector End Views | |||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
2 | Attempt to open the power sliding door (PSD) using both OPEN/CLOSE switches and the remote keyless entry transmitter. Does the PSD open using any of the OPEN/CLOSE switches? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||
3 | Does the sliding door alarm sound a tone when an OPEN/CLOSE switch is pressed? | Go to Step 8 | Go to Step 4 | ||||||
4 |
Does the test lamp flash when the OPEN/CLOSE switch is pressed? | Go to Step 5 | Go to Step 7 | ||||||
5 | Inspect the door lock switch plate for the following conditions:
Did you find and correct the condition? | Go to Step 18 | Go to Step 6 | ||||||
6 | Test the unlatch actuator control and ground circuits from the door lock switch plate plungers to the unlatch actuator connector for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 14 | ||||||
7 | Test the unlatch actuator control circuit from the B-pillar door lock switch plate pads to the rear side door actuator control module connector for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 16 | ||||||
8 |
Does the test lamp illuminate? | Go to Step 9 | Go to Step 10 | ||||||
9 |
Does the PSD open properly? | Go to Step 12 | Go to Step 11 | ||||||
10 | Repair the battery positive voltage supply circuit to the transaxle range switch for an open or high resistance. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | Go to Step 18 | -- | ||||||
11 | Test the park signal circuit to the rear side door actuator control module for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 16 | ||||||
12 | Inspect for poor connections at the transaxle range switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 13 | ||||||
13 | Replace the transaxle range switch. Refer to Park/Neutral Position Switch Replacement in Automatic Transaxle. Is the repair complete? | Go to Step 18 | -- | ||||||
14 | Inspect for poor connections at the unlatch actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 15 | ||||||
15 | Replace the unlatch actuator. Refer to Power Sliding Door Unlatch Actuator Replacement . Is the repair complete? | Go to Step 18 | -- | ||||||
16 | Inspect for poor connections at the rear side door actuator control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 17 | ||||||
17 | Replace the rear side door actuator control module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Is the repair complete? | Go to Step 18 | -- | ||||||
18 | Re-initialize the PSD and operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 | ||||||
