Quarter Window Replacement With A20

Important: Before removing a stationary window, apply a layer of masking tape around the perimeter of the painted surfaces and inner trim of the window.

1. Remove the body side rear upper finish panel. Refer to Body Lock Pillar Upper Trim Panel Replacement in Interior Trim.
2. Remove the rear corner upper finish panel. Refer to Upper Rear Trim Finish Panel Replacement in Interior Trim.
3. Open the bodyside window to the full open position.
4. Disconnect the electrical connector (4) from the power window actuator (5).
5. Remove the bodyside window hinge nuts (2).
6. Remove the bodyside window (1) from the opening.
7. Remove the screw (3) from the window (1).

Notice: Refer to Fastener Notice in the Preface section.




1. Install the bodyside window screw (3) to the window  (1).

Tighten
Tighten the screw (3) to 1.6 N·m (1.4 lb in).

2. Install the bodyside window to the bodyside opening.
3. Install the bodyside window hinge nuts (2).

Tighten
Tighten the nuts (2) to 10 N·m (89 lb in).

4. Connect the electrical connector (4) to the power window actuator (5).
5. Inspect the bodyside window for proper operation.
6. Close the bodyside window.
7. Remove the masking tape from around the perimeter of the painted surfaces and inner trim of the window.
8. Install the rear corner upper finish panel. Refer to Upper Rear Trim Finish Panel Replacement in Interior Trim.
9. Install the body side rear upper finish panel. Refer to Body Lock Pillar Upper Trim Panel Replacement in Interior Trim.

Quarter Window Replacement w/o A20

Tools Required

J 34946 Window Pin Remover

Important: Before removing a bodyside window, apply a layer of masking tape around the perimeter of the painted surfaces and inner trim of the window.

1. If removing the sliding door window garnish molding. Refer to Rear Side Door Garnish Molding Replacement in Interior Trim.
2. If removing the bodyside window garnish molding. Refer to Upper Rear Trim Finish Panel Replacement in Interior Trim.
3. If removing the body side rear upper garnish molding. Refer to Body Lock Pillar Upper Trim Panel Replacement in Interior Trim.
4. Open the bodyside window to the full open position.
5. Use J 34946 or equivalent in order to remove the latch hinge pin.

Remove the bodyside window latch hinge pin (4) from the latch (3).

6. Remove the bodyside window hinge nuts (2) from the body.
7. Remove the bodyside window from the opening.
8. Remove the bodyside window latch hinge screw from the window.
9. Remove the retainers.
10. Remove the bushings.

1. Install the bushings.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the retainers.
3. Install the bodyside window latch hinge screw to the window.

Tighten
Tighten the screw (2) to 1.6 N·m (1.4 lb in).

4. Install the bodyside window in the opening.
5. Install the bodyside window hinge nuts (2) to the body.

Tighten
Tighten the nuts (2) to 3.5 N·m (1.6 lb in).

6. Use J 34946 or equivalent in order to install the latch hinge pin.

Install the bodyside window latch hinge pin (4) to the latch (3).

7. Inspect the bodyside window for proper operation.
8. Close the bodyside window.
9. Install the body side rear upper garnish molding. Refer to Body Lock Pillar Upper Trim Panel Replacement in Interior Trim.
10. Install the bodyside window garnish molding. Refer to Upper Rear Trim Finish Panel Replacement in Interior Trim.
11. Install the sliding door window garnish molding. Refer to Rear Side Door Garnish Molding Replacement in Interior Trim.
12. Remove the masking tape from around the perimeter of the painted surfaces and inner trim of the window.