GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2007 🢒 Vivant 🢒 Steering 🢒 Steering Wheel and Column 🢒 Steering Column Replacement

Removal Procedure

    Caution: Refer to Battery Disconnect Caution in the Preface section.


    Object Number: 1265533 Size: SH

    Notice: The front wheels of the vehicle must be maintained in the straight ahead position and the steering column must be in the LOCK position before disconnecting the steering column or intermediate shaft. Failure to follow these procedures will cause improper alignment of some components during installation and result in damage to the SIR coil assembly.

    Notice: Once the steering column is removed from the vehicle, the column is extremely susceptible to damage. Dropping the column assembly on the end could collapse the steering shaft or loosen the plastic injections, which maintain column rigidity. Leaning on the column assembly could cause the jacket to bend or deform. Any of the above damage could impair the columns collapsible design. Do NOT hammer on the end of the shaft, because hammering could loosen the plastic injections, which maintain column rigidity. If you need to remove the steering wheel, refer to the Steering Wheel Replacement procedure in this section.

    Important: Remove the steering column only if the following conditions exist:

       • The steering column requires replacement.
       • The steering and the ignition lock housing require replacement.
       • Another operation requires the removal of the steering column.

  1. Disconnect the negative battery cable and let the vehicle sit for 1 minute to deactivate the air bag.
  2. Remove the upper and the lower steering column covers by removing the screws.

    3. Object Number: 1265539 Size: SH
  3. Remove the instrument panel (I/P) lower cover.
  4. Disconnect the air bag electrical connectors.
  5. Remove the immobilizer module, if equipped. Refer to Theft Deterrent Module Replacement .

    6. Object Number: 1265540 Size: SH
  6. Disconnect the ignition switch electrical connector.

    7. Object Number: 1263907 Size: SH

    Important: Ensure the steering wheel is in the straight ahead position while the front wheels are in the straight ahead position.

  7. Adjust the steering wheel to the straight-ahead position.
  8. Place a match mark on the steering column shaft and on the intermediate shaft upper universal joint.
  9. Remove the pinch bolt from the intermediate shaft universal joint.

    10. Object Number: 1265544 Size: SH
  10. Remove the steering column lower mounting nuts.

    11. Object Number: 1265547 Size: SH
  11. Remove the steering column upper mounting nuts that hold the rear bracket of the steering column jacket assembly.
  12. Guide the steering column assembly out of the steering shaft flange and carefully lay down the assembly.

Installation Procedure

    Object Number: 1265547 Size: SH

    Important: Ensure the steering wheel is in the straight ahead position while the front wheels are in the straight ahead position.

    Important: Do not let the steering column assembly hang unsupported.

  1. Install the steering column assembly into the steering shaft flange.

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the steering column upper mounting nut.

    3. Tighten
    Tighten the nut to 23 N·m (17 lb ft).


    Object Number: 1265544 Size: SH
  3. Install the steering column lower mounting nuts.

    4. Tighten
    Tighten the nuts to 23 N·m (17 lb ft).


    Object Number: 1263907 Size: SH
  4. Install the pinch bolt into the intermediate shaft universal joint.

    5. Tighten
    Tighten the bolt to 22 N·m (16 lb ft).


    Object Number: 1265540 Size: SH
  5. Connect the ignition switch electrical connector.

    6. Object Number: 1265539 Size: SH
  6. Connect the immobilizer module, if equipped. Refer to Theft Deterrent Module Replacement .
  7. Connect the air bag electrical connectors.
  8. Install the I/P lower cover.

    9. Object Number: 1265533 Size: SH
  9. Install the upper and the lower steering column covers and the screws.
  10. Connect the negative battery cable.