Circuit Description
When the ignition switch is turned to ON, the sensing and diagnostic module (SDM) will perform tests to diagnose critical malfunctions within the SDM itself.
After passing these tests, ignition and deployment loop voltages are measured to ensure that they are within their respective normal voltage ranges. The SDM then proceeds with the resistance measurement test.
Each inflator low terminal is grounded through a current sink, and each inflator current source is connected to each inflator high terminal to allow a known amount of current to flow.
By monitoring the voltage difference between each inflator high and low, the SDM calculates the combined resistance of the inflator module, the wiring harness and the connector terminal contacts.
DTC Descriptor
This diagnostic procedure supports the following DTCs:
| • | DTC B0064 LF Pretensioner Deployment Loop Resistance Low |
| • | DTC B0065 LF Pretensioner Deployment Loop Open |
| • | DTC B0066 LF Pretensioner Deployment Loop Voltage Out of Range |
Conditions for Running the DTC
Ignition voltage is within the normal operating voltage range.
Conditions for Setting the DTC
B0064
DTC B0064 will set when the SDM detects the resistance of driver belt pretensioner deployment loop is lower than 1.4 ohms.
B0065
DTC B0065 will set when the SDM detects the resistance of driver belt pretensioner deployment loop is higher than 4.5 ohms for 500 milliseconds, or voltage at the driver belt pretensioner high is less than 2 volts and resistance of the driver belt pretensioner deployment loop is 4.5 or more ohms for 500 milliseconds.
B0066
DTC B0066 will set when the SDM detects the resistance of driver belt pretensioner high is greater than 7.5 volts for 5 consecutive test cycles, or voltage at the driver belt pretensioner high is less than 1.5 volts and resistance of the driver belt pretensioner deployment loop is less than 6 ohms for 5 consecutive test cycles.
Action Taken When The DTC Sets
The SDM commands the AIR BAG indicator ON.
Conditions for Clearing the DTC
The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
Diagnostic Aids
B0064
An intermittent condition is likely to be caused by a short between the driver belt pretensioner high and low circuits.
B0065
An intermittent condition is likely to be caused by a poor connection at the driver belt pretensioner connector or SDM.
B0066
An intermittent condition is likely to be caused by a short to ground or voltage in the driver belt pretensioner high and low circuits.
Step | Action | Yes | No |
|---|---|---|---|
|
Caution: Refer to Sensing and Diagnostic Module Voltage after Ignition is Turned Off Caution in the Preface section. Caution: Refer to Sensing and Diagnostic Module Handling Caution in the Preface section. Schematic Reference: SIR Schematics Connector End View Reference: SIR Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 | Is DTC B0064, B0065, or B0066 set as a current DTC? | Go to Step 3 | Go to Diagnostic Aids |
3 |
Is the connector disconnected or wiring damaged? | Go to Step 4 | Go to Step 5 |
4 | Connect the driver belt pretensioner connector or replace the wiring. Is the repair complete? | Go to Step 9 | -- |
5 |
For all the above conditions, refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 6 |
6 | Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement . Did you complete the replacement? | Go to Step 7 | -- |
7 |
Does the DTC reset? | Go to Step 8 | System OK |
8 | Replace the driver belt pretensioner. Did you complete the replacement? | Go to Step 9 | -- |
9 |
Does the DTC reset? | Go to Step 2 | -- |
