GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Daewoo 🢒 2009 🢒 G2X 🢒 Engine 🢒 Engine Controls and Fuel - 2.0L 🢒 Fuel Injection Fuel Rail Assembly Replacement

Removal Procedure

    Object Number: 1826857 Size: SH
  1. Disconnect the engine wiring harness electrical connector (1) from the fuel injector wiring harness electrical connector.
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.

    3. Object Number: 1769947 Size: SH
  3. Remove the fuel injector insulator.

    4. Object Number: 1826282 Size: SH
  4. Relieve the high side fuel system pressure. Refer to Fuel Pressure Relief.
  5. Disconnect the engine wiring harness electrical connector (1) from the high pressure fuel pump.

    6. Object Number: 1826280 Size: SH
  6. Remove the high pressure fuel pump cover bolts.
  7. Remove the high pressure fuel pump cover.
  8. Remove the engine wiring harness clip from the high pressure fuel pump cover.

    9. Object Number: 1829002 Size: SH
  9. Remove the high pressure fuel pump insulator.

    10. Object Number: 1828941 Size: SH
  10. Loosen the high pressure fuel pipe fitting at the fuel pump.
  11. Loosen the high pressure fuel pipe fitting at the fuel rail.
  12. Remove and discard the high pressure fuel pipe.

    13. Object Number: 1829953 Size: SH
  13. Disconnect the fuel injector wiring harness electrical connectors from the fuel injectors.
  14. Remove the fuel rail bolts (1).

    15. Note: Carefully remove the fuel rail. The fuel injectors may come out of the cylinder head with the fuel rail.

  15. Carefully remove the fuel rail (2).
  16. If the fuel injectors have been removed with the fuel rail, reinstall the injectors. Refer to Direct Fuel Injector Replacement.

    17. Object Number: 1829979 Size: SH
  17. Remove and discard the fuel injector upper O-ring seal (1).
  18. Inspect the plastic spacer (2) for damage, remove if damaged.

    19. Object Number: 1829977 Size: SH

    Note: Applying force to the plastic housing of the sensor will destroy the sensor. To tighten or loosen, only apply force to the attached hexagon.

  19. If replacing the fuel rail, remove the fuel injection fuel rail fuel pressure sensor.
  20. Remove the fuel injector wiring harness.

Installation Procedure

    Object Number: 1829977 Size: SH
  1. If the fuel rail was replaced, lubricate the threads and sealing cone of the NEW fuel rail with silicon free engine oil GM P/N 12345610 (Canadian P/N 993193) or equivalent.
  2. Lubricate the threads and sealing cone of the sensor with silicon free engine oil GM P/N 12345610 (Canadian P/N 993193) or equivalent.

    3. Caution: Refer to Fastener Caution in the Preface section.

    Note: Applying force to the plastic housing of the sensor will destroy the sensor. To tighten or loosen, only apply force to the attached hexagon.

  3. Install the fuel injection fuel rail fuel pressure sensor and tighten to 33 N·m (25 lb ft).
  4. Install the fuel injector wiring harness.

    5. Object Number: 1829979 Size: SH
  5. Install a NEW plastic spacer (2) if the old one was damaged.
  6. Lubricate a NEW fuel injector upper O-ring seal (1) with silicon free engine oil GM P/N 12345610 (Canadian P/N 993193) or equivalent.
  7. Install the NEW fuel injector upper O-ring seal (1).

    8. Object Number: 1829953 Size: SH
  8. Place the fuel rail (2) into position.
  9. Install the 2 outer fuel rail bolts (1) first hand tight, and then install the remaining 2 bolts, hand tight.
  10. Connect the fuel injector wiring harness electrical connectors to the fuel injectors.

    11. Object Number: 1769965 Size: SH
  11. Tighten the fuel rail bolts in the sequence shown.
    12. • Tighten the bolts a first pass to 22 N·m (16 lb ft).
    • Tighten the bolts a final pass to 22 N·m (16 lb ft).

    Object Number: 1828941 Size: SH
  12. Ensure that the high pressure fuel pump, and fuel rail fittings are clean prior to assembly.
  13. Lubricate the high pressure fuel pump, and the fuel rail fittings with silicon free engine oil GM P/N 12345610 (Canadian P/N 993193) or equivalent.
  14. Install a NEW high pressure fuel pipe.
  15. Tighten the NEW high pressure fuel pipe fitting to the fuel rail hand tight.
  16. Tighten the NEW high pressure fuel pipe fitting to the fuel pump hand tight to 32 N·m (24 lb ft).

    17. Object Number: 1829002 Size: SH
  17. Install the high pressure fuel pump insulator.

    18. Object Number: 1826280 Size: SH
  18. Install the engine wiring harness clip to the high pressure fuel pump cover.
  19. Install the high pressure fuel pump cover.
  20. Install the high pressure fuel pump cover bolts and tighten to 10 N·m (89 lb in).

    21. Object Number: 1826282 Size: SH
  21. Connect the engine wiring harness electrical connector (1) to the high pressure fuel pump.

    22. Object Number: 1769947 Size: SH
  22. Install the fuel injector insulator.
  23. Install the intake manifold. Refer to Intake Manifold Replacement.

    24. Object Number: 1826857 Size: SH
  24. Connect the engine wiring harness electrical connector (1) to the fuel injector wiring harness electrical connector.
  25. Inspect for leaks using the following procedure:
    26. 25.1. Turn ON the ignition, with the engine OFF for 2 seconds.
    25.2. Turn OFF the ignition, for 10 seconds.
    25.3. Turn ON the ignition, with the engine OFF.
    25.4. Inspect for fuel leaks.
  26. Install the low side fuel pressure service port cap.
  27. Tighten the fuel fill cap.
  28. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.