Generator Replacement First Design

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Remove the drive belt. Refer to Drive Belt Replacement .
3. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
4. Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .
5. Remove the air conditioning (A/C) liquid line clamp bolt (2) from the upper radiator support.
6. Unbolt the coolant recovery reservoir from the upper radiator support, and position out of the way.



7. Reposition the battery positive junction block cable boot (1).
8. Remove the battery positive junction block cable to generator nut (2).
9. Remove the battery positive junction block cable terminal (3) from the generator stud.



10. Disconnect the engine wiring harness electrical connector (1) from the generator.



11. Remove the power steering reservoir inlet hose clip (1) from the power steering fluid reservoir hose clip bracket (2).



12. Loosen the idler pulley bolt (1) and slide the pulley out as far as possible.



13. Remove the generator nuts (3).
14. Remove the A/C compressor/evaporator hose bracket (2) from the left generator stud.
15. Remove the power steering fluid reservoir hose clip bracket (1) from the right generator stud.
16. Remove the generator studs.
17. Remove the generator and idler pulley together from the vehicle.
18. Remove the idler pulley from the generator.

1. Install the idler pulley to the generator.
2. Install the generator and idler pulley together to the vehicle.

Notice: Refer to Fastener Notice in the Preface section.

3. Install the generator studs.

Tighten
Tighten the studs to 10 N·m (89 lb in).

4. Install the generator onto the studs.
5. Install the power steering fluid reservoir hose clip bracket (1) to the left generator stud.
6. Install the A/C compressor/evaporator hose bracket (2) to the right generator stud.
7. Install the generator nuts (3) finger tight.



8. Install the idler pulley bolt (1) finger tight.
9. Tighten the generator bolt/nuts in the following sequence to specifications.

9.1.	Idler pulley bolt

9.2.

Left nut

9.3.

Right nut

Tighten
Tighten the bolt/nuts to 50 N·m (37 lb ft).




10. Install the power steering reservoir inlet hose clip (1) to the power steering fluid reservoir hose clip bracket (2).



11. Connect the engine wiring harness electrical connector (1) to the generator.



12. Install the battery positive junction block cable terminal (3) to the generator stud.
13. Install the battery positive junction block cable to generator nut (2).

Tighten
Tighten the nut to 22 N·m (16 lb ft).

14. Position the battery positive junction block cable boot (1) over the stud.



15. Position and bolt the coolant recovery reservoir to the upper radiator support.

Tighten
Tighten the bolt to 5 N·m (44 lb in).

16. Install the A/C liquid line clamp bolt (2) at the upper radiator support.

Tighten
Tighten the bolt to 9 N·m (80 lb in).

17. Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .
18. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
19. Install the drive belt. Refer to Drive Belt Replacement .
20. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Generator Replacement Second Design

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Remove the drive belt. Refer to Drive Belt Replacement .
3. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
4. Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .
5. Remove the air conditioning (A/C) liquid line clamp bolt (2) from the upper radiator support.



6. Remove the coolant recovery reservoir bolts (1).
7. Remove the reservoir (2) tabs from the upper radiator support, position the reservoir out of the way.



8. Reposition the battery positive junction block cable boot (1).
9. Remove the battery positive junction block cable to generator nut (2).
10. Remove the battery positive junction block cable terminal (3) from the generator stud.



11. Disconnect the engine wiring harness electrical connector (1) from the generator (2).



12. Remove the power steering reservoir inlet hose clip (1) from the power steering fluid reservoir hose clip bracket (2).



13. Loosen the idler pulley (1) bolt and slide the pulley out as far as possible.



14. Remove the generator bolts (2).
15. Remove the A/C compressor/evaporator hose bracket (1) from against the generator.
16. Remove the power steering fluid reservoir hose clip bracket (3) from against the generator.
17. Remove the generator (4) and idler pulley (5) together from the vehicle.
18. Remove the idler pulley from the generator.

1. Install the idler pulley (5) to the generator.
2. Install the generator (4) and idler pulley together to the vehicle.
3. Install the power steering fluid reservoir hose clip bracket (1) onto one of the generator bolts, and install the bolt finger tight.
4. Install the A/C compressor/evaporator hose bracket (2) onto the other generator bolt, and install the bolt finger tight.

Notice: Refer to Fastener Notice in the Preface section.

5. Tighten the idler pulley/generator bolts (2) in the following sequence:

5.1.	Idler pulley bolt

5.2.	Generator bolts

Tighten
Tighten the bolts to 50 N·m (37 lb ft).




6. Install the power steering reservoir inlet hose clip (1) to the power steering fluid reservoir hose clip bracket (2).



7. Connect the engine wiring harness electrical connector (1) to the generator.



8. Install the battery positive junction block cable terminal (3) to the generator stud.
9. Install the battery positive junction block cable to generator nut (2).

Tighten
Tighten the nut to 22 N·m (16 lb ft).

10. Position the battery positive junction block cable boot (1) over the stud.



11. Install the coolant recovery reservoir (2) tabs into the appropriate slots in the upper radiator support .
12. Install the coolant recovery reservoir bolts (1).

Tighten
Tighten the bolts to 5 N·m (44 lb in).




13. Install the A/C liquid line clamp bolt (2) at the upper radiator support.

Tighten
Tighten the bolt to 9 N·m (80 lb in).

14. Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .
15. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
16. Install the drive belt. Refer to Drive Belt Replacement .
17. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .