GM Service Manual Online
For 1990-2009 cars only

Dash/Instrument Panel Foam Closeout Seal Distorted, Wavy, Loose and/or Seal Could Partially Cover VIN Plate (Replace Instrument Panel Outer Seal)

Subject:Dash/Instrument Panel Foam Closeout Seal Distorted, Wavy, Loose and/or Seal Could Partially Cover VIN Plate (Replace Instrument Panel Outer Seal)

Models:2004-2007 Chevrolet Colorado
2004-2007 GMC Canyon



Condition


Object Number: 1972800  Size: SH

Some customers may comment on a distorted, wavy, loose seal around the dash/instrument panel (IP) and the IP seal could partially cover the VIN plate as shown above.

Cause

The adhesive backing on the IP outer seal may become loose.

Correction

Replace the IP outer seal using the procedure listed below:

  1. Disable the SIR system. Refer to SIR Disabling and Enabling in SI.
  2. Remove the left and right windshield garnish moldings. Refer to Windshield Pillar Garnish Molding Replacement in SI.
  3. Remove the three upper IP trim covers and nuts located on the top of the IP pad.
  4. Remove the knee bolster trim panel. Refer to Driver Knee Bolster Panel Replacement in SI.
  5. Remove the knee bolster. Refer to Knee Bolster Replacement in SI.

  6. Object Number: 1975003  Size: SH
  7. Disconnect the HVAC mode cable (1) from the mode control cam.
  8. Disconnect the steering column electrical connectors.
  9. Remove the four steering column bolts and position the steering column assembly down onto the drivers floor.

  10. Object Number: 1974995  Size: SH
  11. Remove the two carrier bolts (1) from the brake pedal/steering column support bracket.
  12. Remove the left IP end trim panel.

  13. Object Number: 1974990  Size: SH
  14. Remove the two left carrier bolts (1).
  15. Remove the right IP end trim panel.

  16. Object Number: 1974999  Size: SH
  17. Remove the two right carrier bolts (1).
  18. Remove the right front door sill plate. Refer to Front Door Sill Plate Replacement in SI.
  19. Remove the right hinge pillar trim panels. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side in SI.

  20. Object Number: 1975000  Size: SH
  21. Remove the right lower carrier bolt (1).
  22. Remove the lower center IP extension. Refer to Instrument Panel Lower Center Trim Replacement in SI.

  23. Object Number: 1975001  Size: SH
  24. Remove the two center lower carrier bolts (1).

  25. Object Number: 1975007  Size: SH

    Object Number: 1975005  Size: SH

    Important: You may need an assistant to help lift up and pull back on the IP carrier assembly to release the attaching hook from the right side bracket. The hook on the IP carrier and the sheet metal bracket are shown above.


    Object Number: 1975008  Size: SH
  26. Reposition the complete IP carrier assembly as shown above.
  27. Tip
    A heat gun may be used to help remove the old seal and glue, if necessary.

  28. Remove the old IP outer seal and discard.
  29. Cover and protect the rear and top of the IP panel before cleaning.
  30. Using a shop towel with Acrysol™ or equivalent applied, clean the IP pad sealing edge ONLY .
  31. Important: The notched portion of the seal is for the VIN plate. Make sure the adhesive backing on the foam seal is adhering to the IP pad edge. If the seal is not adhering, reclean the sealing area with denatured alcohol and install the seal.

  32. Install the new IP outer seal starting at the right side of the instrument panel and working toward the left side while pushing down on the seal.
  33. Remove the cover and reposition the IP carrier assembly back into position with the help of an assistant.
  34. Verify the IP outer seal is not seen in the VIN plate area.
  35. Install the two right side IP carrier bolts and tighten.
  36. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  37. Install the right side IP end trim panel.
  38. Install the right lower carrier bolt and tighten.
  39. Tighten
    Tighten the bolt to 9 N·m (80 lb in).

  40. Install the right front door sill plate. Refer to Front Door Sill Plate Replacement in SI.
  41. Install the right hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side in SI.
  42. Install the two lower center IP carrier bolts and tighten.
  43. Tighten
    Tighten the bolts to 9 N·m (80 lb in).

  44. Install the lower center IP extension. Refer to Instrument Panel Lower Center Trim Replacement in SI.
  45. Install the two carrier bolts to the brake pedal/steering column support bracket.
  46. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  47. Install the steering column and the four steering column bolts.
  48. Tighten the steering column bolts.
  49. Tighten
    Tighten the bolts to 27 N·m (20 lb ft).

  50. Connect the steering column electrical connectors.
  51. Connect the HVAC mode cable to the mode control cam.
  52. Install the knee bolster. Refer to Knee Bolster Replacement in SI.
  53. Install the knee bolster trim panel. Refer to Driver Knee Bolster Panel Replacement in SI.
  54. Install the three upper IP nuts located on the top of the IP and tighten.
  55. Tighten
    Tighten the nuts to 9 N·m (80 lb in).

  56. Install the three upper IP trim covers located on the top of the IP.
  57. Install the two left side IP carrier bolts and tighten.
  58. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  59. Install the left side IP end trim panel.
  60. Install the left windshield garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in SI.
  61. Enable the SIR system. Refer to SIR Disabling and Enabling in SI.

Parts Information

Part Number

Description

Qty

15197840

Seal, IP Outer

1

Warranty Information

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

C9790*

I/P Outer Seal - Replace

1.2 hrs

*This is a unique labor operation for bulletin use only. This number will not be published in the Labor Time Guide.