Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC C0186 00: Lateral Accelerometer CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Lateral Accelerometer Supply Voltage Circuit | C0186 00 | C0186 00 | C0186 00 | -- |
Lateral Accelerometer CAN Bus High Circuit | C0186 00 | C0186 00 | C0186 00 | C0186 00 |
Lateral Accelerometer CAN Bus Low Circuit | C0186 00 | C0186 00 | C0186 00 | C0186 00 |
Lateral Accelerometer Ground Circuit | -- | C0186 00 | -- | -- |
Circuit/System Description
The lateral accelerometer and the yaw rate sensors are combined into one sensor external to the electronic brake control module (EBCM). The vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The usable output signal is a serial data CAN circuits.
Conditions for Running the DTC
The ignition switch is in the ON position.
Conditions for Setting the DTC
| • | The yaw/lateral combination sensor reports an internal failure. |
| • | The yaw/lateral combination sensor learns a wrong offset value. |
| • | Incorrectly mounted yaw/lateral sensor. |
Action Taken When the DTC Sets
One or more of the following actions may occur:
| • | VSES is disabled. |
| • | A DIC message and/or a warning indicator may be displayed. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present. |
| • | The EBCM automatically clears the history DTC when a current DTC is not detected in 50 consecutive drive cycles. |
Diagnostic Aids
Possible causes of this DTC are as follows:
| • | Incorrectly mounted yaw/lateral sensor |
| • | Internal failure in the yaw/lateral sensor |
| • | Intermittent wiring connections |
Reference Information
Schematic Reference
Antilock Brake System Schematics
Connector End View Reference
Description and Operation Reference
Electrical Information Reference
Scan Tool Reference
Control Module References for Scan Tool Information
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the Yaw Rate/Lateral Accelerometer sensor.
- Test for less than 1 ohm between the low reference circuit terminal 5 and ground.
- Ignition ON, test for ignition voltage between the ignition circuit terminal 3 and the low reference circuit terminal 5.
- Ignition OFF, disconnect the harness connector at the EBCM.
- Test for infinite resistance between the low reference circuit terminal 29 and ground.
- Ignition ON, test for 0 volts between the communication circuit terminal 18 and ground at the EBCM harness connector.
- Test for 0 volts between the communication circuit terminal 19 and ground.
- Ignition OFF, test for infinite resistance between the communication circuit terminal 18 and ground.
- Test for infinite resistance between the communication circuit terminal 19 and ground.
- Test for less than 1 ohm between the communication circuit terminals 18 and terminal 2.
- Test for less than 1 ohm between the communication circuit terminals 19 and terminal 1.
- Test for infinite resistance between the communication circuit 18 and the communication circuit 19.
- If all circuits test normal, replace the Yaw Rate/Lateral sensor.
| ⇒ | If greater than the specified range, test for an open/high resistance in the low reference circuit. |
| ⇒ | If not the specified value, test the ignition circuit for a short to ground or an open/high resistance. |
| ⇒ | If greater than the specified value, test the low reference circuit for a short to ground. |
| ⇒ | If greater than the specified value, test the communication circuit for a short to voltage. |
| ⇒ | If greater than the specified value, test the communication circuit for a short to voltage. |
| ⇒ | If not the specified value, test the communication circuit for a short to ground. |
| ⇒ | If not the specified value, test the communication circuit for a short to ground. |
| ⇒ | If greater than the specified range, test the communication circuit for an open/high resistance. |
| ⇒ | If greater than the specified range, test the communication circuit for an open/high resistance. |
| ⇒ | If not the specified value, test the communication circuits for a short together. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for EBCM replacement, setup and programming |
