Circuit Description
The fuel tank pressure (FTP) sensor measures the difference between the air pressure or vacuum in the evaporative emission (EVAP) system, and the outside air pressure. The control module supplies a 5-volt reference and a low reference circuit to the FTP sensor. The FTP sensor signal circuit voltage varies depending on EVAP system pressure or vacuum. If the FTP sensor signal voltage goes below a calibrated value, this DTC sets.
The following table illustrates the relationship between the FTP sensor signal voltage and the EVAP system pressure/vacuum.
FTP Sensor Signal Voltage | Fuel Tank Pressure |
|---|---|
High, Approximately 1.5 Volts or More | Negative Pressure/Vacuum |
Low, Approximately 1.5 Volts or Less | Positive Pressure |
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0452 Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage
Conditions for Running the DTC
| • | The ignition is ON. |
| • | DTC P0452 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
| • | The FTP voltage is less than 0.1 volt. |
| • | The above condition is present for more than 5 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that the condition is present.
-
This step tests the 5-volt reference of the FTP sensor.
-
This step tests if another component is causing the 5-volt reference circuit condition.
-
If the scan tool displays 5 volts, the FTP sensor signal circuit, the FTP sensor 5-volt reference circuit, and the control module are OK.
Step | Action | Values | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | ||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
Observe the Fuel Tank Pressure Sensor parameter with a scan tool. Is the Fuel Tank Pressure Sensor parameter less than the specified value? | 0.1 V | Go to Step 4 | Go to Step 3 | |||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions | ||||||
Is the voltage within the specified value? | 4.8-5.2 V | Go to Step 6 | Go to Step 5 | |||||||
Disconnect the following components, while monitoring the DMM:
Is the DMM within the specified value when any of the components are disconnected? | 4.8-5.2 V | Go to Step 11 | Go to Step 7 | |||||||
Is Fuel Tank Pressure Sensor parameter within the specified value? | 4.8-5.2 V | Go to Step 9 | Go to Step 8 | |||||||
7 | Test the FTP 5-volt reference circuit for an open or for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 | ||||||
8 | Test the FTP signal circuit for an open or for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 | ||||||
9 | Test for an intermittent and for a poor connection at the FTP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 | ||||||
10 | Test for an intermittent and for a poor connection at the control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 | ||||||
11 | Replace the component that affected the 5-volt reference circuit. Refer to Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement in Heating, Ventilation and Air Conditioning, Throttle Body Assembly Replacement , or Manifold Absolute Pressure Sensor Replacement. Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||
12 | Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||
13 | Replace the powertrain control module (PCM). Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||
14 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 15 | ||||||
15 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK | ||||||
