Rear Hatch/Gate Ajar Indicator Malfunction. GMC Truck Envoy XUV 2005

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 2005 🢒 Envoy XUV 🢒 Body 🢒 Body Rear End 🢒 Rear Hatch/Gate Ajar Indicator Malfunction

Step	Action	Yes	No
Schematic Reference: Body Rear End Schematics Connector End View Reference: Body Rear End Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	Go to Step 2	Go to Diagnostic System Check - Vehicle
2	Verify that the rear hatch/gate ajar indicator is malfunctioning. Does the rear hatch/gate ajar indicator operate normally?	Go to Testing for Intermittent Conditions and Poor Connections	Go to Step 3
3	Is the rear hatch/gate ajar indicator always ON?	Go to Step 4	Go to Step 6
4	Install a scan tool. Close the liftglass and liftgate. Turn ON the ignition, with the engine OFF. With a scan tool, observe the liftgate ajar switch and liftglass ajar switch parameters in the Liftgate Module data list. Does the scan tool display Ajar?	Go to Step 5	Go to Step 11
5	Disconnect the appropriate liftgate ajar or liftglass ajar switch. Does the scan tool display Ajar?	Go to Step 8	Go to Step 12
6	Install a scan tool. Open the liftglass and liftgate. Turn ON the ignition, with the engine OFF. With a scan tool, observe the liftgate ajar switch and liftglass ajar switch parameters in the Liftgate Module data list. Does the scan tool display Ajar?	Go to Step 11	Go to Step 7
7	Turn OFF the ignition. Disconnect the appropriate liftgate ajar or liftglass ajar switch. Turn ON the ignition, with the engine OFF. Connect a fused jumper between the appropriate ajar switch signal circuit and the appropriate ajar switch low reference circuit of the ajar switch harness connector. Does the scan tool display Ajar?	Go to Step 12	Go to Step 9
8	Test the liftgate ajar switch signal circuit or the liftglass ajar switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	Go to Step 17	Go to Step 13
9	Test the liftgate ajar switch signal circuit or the liftglass ajar switch signal circuit for an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	Go to Step 17	Go to Step 10
10	Test the liftgate ajar switch low reference circuit or the liftglass ajar switch low reference circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 17	Go to Step 13
11	Inspect for poor connections at the harness connector of the instrument panel cluster. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	Go to Step 17	Go to Step 14
12	Inspect for poor connections at the harness connector of the appropriate ajar switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	Go to Step 17	Go to Step 15
13	Inspect for poor connections at the harness connector of the liftgate module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	Go to Step 17	Go to Step 16
14	Replace the instrument panel cluster. Refer to Instrument Cluster Replacement . Did you complete the repair?	Go to Step 17	--
15	Replace the appropriate ajar switch. Did you complete the replacement?	Go to Step 17	--
16	Replace the liftgate module. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement?	Go to Step 17	--
17	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 2