Circuit Description
The brake switch informs the electronic brake control module (EBCM) when the brake is depressed. The brake switch is normally closed, supplying 12 volts to the EBCM when the brake is released. When the brake pedal is pressed, voltage on the torque converter clutch (TCC) brake switch signal circuit is 0 volts.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0161 Antilock Brake System (ABS) / Traction Control System (TCS) Brake Switch
Conditions for Running the DTC
Any of the following conditions may cause the diagnostic trouble code (DTC) to run.
| • | The vehicle accelerates from 0 km/h (0 mph) to a speed greater than 56 km/h (35 mph). |
| • | The vehicle experiences an ABS event involving all hydraulic circuits. |
Conditions for Setting the DTC
Any of the following conditions may cause the DTC to set.
| • | Voltage on the TCC brake switch signal circuit is always low. |
| • | Voltage on the TCC brake switch signal circuit is always high. |
Action Taken When the DTC Sets
The EBCM stores this information-only DTC for as long as the condition is present.
Conditions for Clearing the DTC
The Conditions for Setting the DTC are no longer present and you use the scan tool Clear DTCs function.
Diagnostic Aids
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to Testing for Intermittent Conditions and Poor Connections , Connector Repairs , Testing for Electrical Intermittents and to Wiring Repairs in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Does the scan tool display Off? | Go to Step 3 | Go to Step 5 |
3 |
Does the scan tool display On? | Go to Diagnostic Aids | Go to Step 4 |
Does the scan tool display On? | Go to Step 9 | Go to Step 7 | |
Does the scan tool display Off? | Go to Step 9 | Go to Step 6 | |
6 | Test the ignition 3 voltage circuit and the TCC brake switch signal circuit for an open or a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
7 | Test the TCC brake switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
8 | Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
10 |
Important: Following EBCM replacement, use the scan tool to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Control Module References in Computer/Intergrating Systems for replacement, setup and programming. Did you complete the replacement? | Go to Step 12 | -- |
11 | Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement in Lighting Systems. Did you complete the replacement? | Go to Step 12 | -- |
12 |
Does the DTC reset? | Go to Step 2 | System OK |
