GM Service Manual Online
For 1990-2009 cars only

Circuit Description

When the body control module (BCM) senses a request for headlamp or daytime running lamp (DRL) illumination, the BCM sends a pulse width modulated (PWM) ground signal to the low beam headlamp driver module through the low beam headlamp driver module control circuit. The low beam headlamp driver module will illuminate the headlamps, adjusting the intensity based on the PWM signal received.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B2575 Headlamp Control Circuit

Conditions for Running the DTC

The battery voltage must be between 9-16 volts.

Conditions for Setting the DTC

    • When the BCM receives a command to illuminate the low beam or DRL headlamps and the low beam headlamp driver module control circuit is open or shorted to voltage.
    • When the BCM does not receive a command to illuminate the low beam or DRL headlamps and the low beam headlamp driver module control circuit is shorted to ground.

Action Taken When the DTC Sets

The low beam and DRL headlamps will not operate or will remain always on.

Conditions for Clearing the MIL/DTC

    • This DTC will clear on current status after the condition for setting the fault is corrected.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History and current DTCs can be cleared using a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for voltage at the voltage supply side of the low beam headlamp driver module.

  2. This step verifies that the BCM is providing PWM ground to the low beam headlamp driver module.

  3. This step tests if ground is constantly being applied to the low beam headlamp driver module.

  4. This step tests if there is opposing voltage present or an open low beam headlamp driver module control circuit.

  5. After replacement of the BCM you must calibrate the new module for proper operation.

Step

Action

Yes

No

Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics

Connector End View Reference: Lighting Systems Connector End Views or Data Communication Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Daytime Running Lamps ON and OFF.

Does the low beam headlamp driver module turn ON and OFF with each command?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the low beam headlamp driver module.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the battery positive voltage circuit of the low beam headlamp driver module with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 4

Go to Step 10

4

  1. Connect a test lamp between the control circuit of the low beam headlamp driver module and the battery positive voltage circuit of the low beam headlamp driver module.
  2. With a scan tool, command the low beam headlamp driver module ON and OFF .

Does the test lamp turn ON and OFF with each command?

Go to Step 8

Go to Step 5

5

Does the test lamp remain illuminated with each command?

Go to Step 7

Go to Step 6

6

Test the control circuit of the low beam headlamp driver module for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 13

Go to Step 9

7

Test the control circuit of the low beam headlamp driver module for a short to ground. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 13

Go to Step 9

8

Inspect for poor connections at the low beam headlamp driver module. Refer to Circuit Testing and Wiring Repairs s.

Did you find and correct the condition?

Go to Step 13

Go to Step 11

9

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 13

Go to Step 12

10

Repair the battery positive voltage circuit of the low beam headlamp driver module. Refer to Wiring Repairs .

Did you complete the repair?

Go to Step 13

--

11

Replace the low beam headlamp driver module. Refer to Relay Replacement .

Did you complete the replacement?

Go to Step 13

--

12

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 13

--

13

  1. Use the scan tool in order to clear the DTCs .
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK