• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
FTP Sensor Signal Voltage | Fuel Tank Pressure |
---|---|
1.5 V | Atmospheric Pressure/BARO |
Less than 1.5 V | Positive Pressure |
More than 1.5 V | Negative Pressure/Vacuum |
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path that would cause excess amounts of vacuum to be developed in the EVAP system. With the purge valve open and the canister vent valve open, if the EVAP system vacuum goes above a calibrated threshold, the test will fail.
• | DTCs P0106, P0107, P0108, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0442, P0443, P0449, P0451, P0452, P0453, P0454, P0464, P0496, P0608, P0609, P0641, P0651, P1516, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138 are not set. |
• | The ignition voltage is between 11-18 volts. |
• | The barometric pressure (BARO) is more than 74 kPa. |
• | The fuel level is between 15-85 percent. |
• | The engine coolant temperature (ECT) is less than 35°C (95°F). |
• | The intake air temperature (IAT) is between 4-30°C (39-86°F). |
• | DTC P0446 runs once per cold start when the above conditions are met. |
• | The fuel tank vacuum is greater than 12 inches H2O vacuum for 5 seconds. |
OR |
• | The fuel tank pressure (FTP) is less than -2.5 inches H2O or more than +5 inches for 60 seconds after a cold start. |
DTC P0446 is a Type B DTC.
DTC P0446 is a Type B DTC.
• | An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill condition. |
• | An EVAP canister filter that is restricted can cause this DTC to set. |
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Control Module References for scan tool information
⇒ | If not within the specified range, go to the FTP sensor section in Circuit/System Testing. |
⇒ | If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing. |
Important: Perform the Circuit/System Verification before proceeding with the Circuit/System Testing.
With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 11 inches H2O.
⇒ | If the fuel tank vacuum is greater than the specified value, isolate the restriction by disconnecting one component at a time while the EVAP canister purge solenoid valve is commanded to 100 percent and the vent valve is open. |
⇒ | If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the FTP sensor. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
With the engine running, the EVAP canister vent solenoid valve open and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 11 inches H2O.