Circuit Description
The engine coolant temperature (ECT) sensor is a variable resistor that measures the temperature of the engine coolant. The powertrain control module (PCM) supplies 5 volts to the signal circuit. When coolant temperatures are low, resistance is high. When coolant temperatures are high the resistance is low. The PCM uses this input for engine controls and enabling criteria for diagnostics. The PCM will record the amount of time the engine is OFF. At restart the PCM will compare the temperature difference between the ECT and intake air temperature (IAT). If the temperature difference is not within the calculated amount, after the predetermined soak time, this DTC will set.
Before failing this test, the PCM will check for the presence of a block heater.
Conditions for Running the DTC
| • | The ignition is ON. |
| • | DTCs P0112, P0113, P0117, P0118, P0125, P0128, P0601, P0602, P0604, P0606, P1481, P1482, P1484, P1621, or P1683 are not set. |
| • | The vehicle has a minimum soak time of 8 hours. |
| • | The intake air temperature (IAT) is more than 15°C (59°F). |
Conditions for Setting the DTC
The temperature difference between the ECT and the IAT at start up is more than 15°C (59°F) .
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | DTC P0116 is designed to detect an ECT sensor that is skewed high. |
| • | An IAT sensor that is skewed could cause this DTC to set. |
| • | When checking the ECT sensor, the Temperature vs Resistance table should be used in order to determine if a skewed sensor is the problem. |
| • | If the engine has been allowed to sit overnight, the ECT and IAT temperature should be within the calculated amount. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for excessive resistance in the ECT sensor circuit.
-
This step tests for excessive resistance in the IAT sensor circuit.
-
This step tests for a skewed sensor through the range of temperatures affecting this DTC.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 | Is the cooling system low on coolant? | -- | Go to Loss of Coolant in Engine Cooling | Go to Step 3 |
Does the scan tool indicate that the ECT sensor temperature is more than the specified value? | 138°C (280°F) | Go to Step 4 | Go to Step 5 | |
Does the scan tool indicate that the IAT sensor temperature is more than the specified value? | 138°C (280°F) | Go to Step 8 | Go to Diagnostic Aids | |
Does the scan tool indicate that the ECT sensor temperature is more than the specified value? | 138°C (280°F) | Go to Step 6 | Go to Step 7 | |
6 |
Did you find and correct the condition? | -- | Go to Step 11 | -- |
7 |
Did you find and correct the condition? | -- | Go to Step 11 | -- |
8 |
Does the resistance and temperature closely match the Temperature vs Resistance table? | 10-90°C (50-194°F) | Go to Step 9 | Go to Step 10 |
9 | Reinstall the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement . Is the action complete? | -- | Go to Diagnostic Aids | -- |
10 | Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- |
11 |
Does the DTC run and pass? | -- | Go to Step 12 | Go to Step 2 |
12 | Observe the stored information, Capture Info., with a scan tool. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
