Schematic Reference: Memory Seats Schematics

Connector End View Reference: Power Seat Connector End Views

Important: This table assumes that all mechanical linkage and drivers are free from obstruction and not binding. This table also assumes that all other directions are operational.

Did you perform the Power Seat Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Power Seat Systems

Operate the horizontal adjuster switch in the forward and rearward directions.

Does the horizontal adjuster motor operate normally?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

1. Install a scan tool.
2. Observe the horizontal position switch parameter in the seat module Inputs/Outputs data list.
3. Operate the horizontal adjuster switch in the forward direction.

Does the scan tool display the correct switch status parameter in relation to the actual switch position?

Go to Step 4

Go to Step 5

Operate the horizontal adjuster switch in the rearward direction.

Does the scan tool display the correct switch status parameter in relation to the actual switch position?

Go to Step 7

Go to Step 6

1. Disconnect the seat adjuster switch connector.
2. Connect a 3 amp fused jumper wire between the battery voltage supply circuit terminal and the horizontal forward switch signal circuit terminal in the harness connector.
3. Observe the horizontal position switch parameter in the seat module Inputs/Outputs data list.

Does the scan tool display the horizontal switch status parameter as forward?

Go to Step 12

Go to Step 8

1. Disconnect the seat adjuster switch connector.
2. Connect a 3 amp fused jumper wire between the battery voltage supply circuit terminal and the horizontal rearward switch signal circuit terminal in the harness connector.
3. Observe the horizontal position switch parameter in the seat module Inputs/Outputs data list.

Does the scan tool display the horizontal switch status parameter as rearward?

Go to Step 12

Go to Step 9

1. Disconnect the horizontal adjuster motor control circuit connector.
2. Connect a test lamp between the control circuit terminals in the harness connector.
3. Operate the horizontal adjuster switch in both directions.

Does the test lamp illuminate in the forward and backward switch positions only?

Go to Step 11

Go to Step 10

Test the horizontal forward switch signal circuit for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

Test the horizontal rearward switch signal circuit for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

Test the horizontal adjuster motor control circuits for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

Inspect for poor connections at the horizontal adjuster motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 14

Inspect for poor connections at the seat adjuster switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in the Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 15

Inspect for poor connections at the seat module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in the Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 16

Replace the horizontal adjuster motor. Refer to Power Seat Adjuster Mechanism Replacement .

Is the repair complete?

Go to Step 17

--

Replace the seat adjuster switch. Refer to Power Seat Switch Replacement .

Is the repair complete?

Go to Step 17

--

Replace the seat module. Refer to Memory Seat Control Module Replacement .

Is the repair complete?

Go to Step 17

--

Operate the system to verify the repair.

Did you correct the condition?

System OK

Go to Step 2