GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2002 🢒 Envoy - 4WD 🢒 Bulletins 🢒 SMU - Revised Wiper Inoperative-Rear Diagnostic

SMU - Revised Wiper Inoperative-Rear Diagnostic

Subject:Revised Wiper Inoperative-Rear Diagnostic

Models:2002 Chevrolet TrailBlazer, TrailBlazer EXT
2002 GMC Envoy, Envoy XL
2002 Oldsmobile Bravada


This bulletin is being issued to revise the Wiper Inoperative-Rear diagnostic in the Wipers/Washer Systems sub-section of the Service Manual. Please replace the current information in the Service Manual with the following information.

The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. If any of the liftgate or liftglass switch fails ajar the rear wiper will not operate.

    2.

  2. This step determines if the liftgate control module is receiving the correct switch position message from the body control module.

    3.

  3. This step determines if the liftgate control module is attempting to operate rear wiper motor in the requested operating mode.

    4.

  4. This step tests the resistance through the rear wiper switch. The measured resistance will be highest in the OFF position and reduce as the switch is turned from positions 1 through 3.

Step

Action

Value(s)

Yes

No

Schematic Reference: Wiper/Washer System Schematics

Connector End View Reference: Wiper/Washer System Connector End Views

DEFINITION: One or more of the rear wiper operating modes are inoperative.

1

Did you perform the Wiper/Washer System Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check-Wiper/Washer

2
  1. Turn the ignition ON.
  2. Operate the rear wiper switch through all the switch positions.

Does the rear window wiper operate normally?

--

Go to Testing for Intermittent and Poor Connections in Wiring Systems

Go to Step 3

3
  1. Install a scan tool.
  2. Display the liftgate control module data list.
  3. Observe the following parameters while operating the respective switches. Refer to Scan Tool Data List for typical values.
    4. • Liftgate Ajar Switch
    • Liftglass Ajar Switch

Did the scan tool indicate the correct switch positions?

--

Go to Courtesy Lamps Inoperative in Lighting Systems

Go to Step 4

4

  1. Observe the requested rear wiper parameter in LGM data list.
  2. Operate the rear wiper switch through all the switch positions.

Does the scan tool indicate the correct requested rear wiper parameter in relation to the switch position?

--

Go to Step 5

Go to Step 6

5

  1. Ensure that the liftgate and liftgate glass are closed and latched.
  2. Observe the rear wiper mode parameter.
  3. Operate the rear wiper switch through all the switch positions.

Does the scan tool indicate the correct rear wiper mode parameter in relation to the switch position?

--

Go to Step 7

Go to Step 18

6

  1. Turn the ignition OFF.
  2. Disconnect the rear wiper switch.
  3. Measure the resistance through the rear wiper switch from the switch power circuit terminal to the signal circuit terminal.
  4. Operate the rear wiper switch through the following switch positions:
    5. • OFF
    • 1
    • 2
    • 3

Does the resistance remain within the specified values from OFF to 3 as the switch is operated through the listed switch positions?

3100-1500 ohms

Go to Step 15

Go to Step 11

7
  1. Turn the ignition OFF.
  2. Disconnect the rear wiper motor connector.
  3. Test the rear wiper motor battery voltage supply circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 8

8

Test the rear wiper motor ground circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 9

9
  1. Connect a test lamp between battery voltage circuit and the control circuit of the rear wiper motor connector.
  2. Close the liftglass and liftgate.
  3. Turn ON the ignition with the engine OFF.
  4. Turn the rear wiper switch from OFF to 3.

Did the brightness of the test lamp decrease gradually as the rear wiper switch was turned from OFF to 3?

--

Go to Step 13

Go to Step 10

10

Test the rear wiper motor control circuit for an open, a short to ground or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 18

11

Inspect for poor connections at the rear wiper switch. Refer to Testing for Intermittent and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 12

12

Replace the rear wiper switch. Refer to Wiper/Washer Switch Replacement-Rear.

Is the repair complete?

--

Go to Step 20

--

13

Inspect for poor connections at the rear wiper motor. Refer to Testing for Intermittent and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 14

14

Replace the rear wiper motor. Refer to Wiper Motor Replacement-Rear.

Is the repair complete?

--

Go to Step 20

--

15

Test the rear window wiper switch signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 16

16

Inspect for poor connections at the BCM. Refer to Testing for Intermittent and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 17

17

Important: Perform the setup procedure for the BCM.

Replace the BCM. Refer to Body Control Module Replacement in Body Control System.

Is the repair complete?

--

Go to Step 20

--

18

Inspect for poor connections at the liftgate control module. Refer to Testing for Intermittent and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 20

Go to Step 19

19

Important: Perform the setup procedure for the liftgate control module.

Replace the liftgate control module. Refer to Lift Gate Control Module Replacement in Body Rear End.

Is the repair complete?

--

Go to Step 20

--

20

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 4