DTC P0237 Turbocharger Boost Sensor Circuit Low Voltage. GMC Truck GMC C Pickup

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 2000 🢒 GMC C Pickup - 2WD 🢒 Engine 🢒 Engine Controls - 6.5L (L65) 🢒 DTC P0237 Turbocharger Boost Sensor Circuit Low Voltage

Engine Controls Components
Engine Data Sensors-ECT, IAT, and Boost (BARO) Sensor
Handling ESD Sensitive Parts Notice
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The powertrain control module (PCM) controls boost using the turbocharger wastegate solenoid. The solenoid is pulse width modulated (PWM). When the wastegate solenoid is not energized, the vacuum to the turbocharger wastegate solenoid is vented to atmosphere through the solenoid. As the pulse width is increased by the PCM, more vacuum is applied through the solenoid to the wastegate actuator. At idle a higher vacuum to the wastegate actuator helps keep the wastegate closed. At higher engine speeds the vacuum supplied by the solenoid is less, allowing the turbocharger boost pressure to overcome the wastegate actuator.

Conditions for Running the DTC

•	The PCM performs this DTC diagnostic continuously.

•	The ignition switch is in the ON position.

Conditions for Setting the DTC

•	The boost pressure is less than 40 kPa.

•	All diagnostic conditions met for 10 seconds.

Action Taken When the DTC Sets

•	The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive drive trip that the diagnostic runs and fails.

•

The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the Failure Records will store this information. If the diagnostic reports a failure on the second consecutive drive trip, the Freeze Frame records the operating conditions at the time of failure and updates the Failure Records.

Conditions for Clearing the MIL/DTC

•	The PCM will turn the MIL off after three consecutive trips without a fault condition.

•	A History DTC clears after forty consecutive warm-up cycles, if this or any other emission related diagnostic does not report any failures.

•	The use of a scan tool.

Diagnostic Aids

Very little boost can be attained by revving the engine in neutral. If the boost sensor signal circuit is open or shorted to ground, the boost solenoid will show a zero duty cycle.

An intermittent may be caused by the following:

•	Poor connections

•	Rubbed through wire insulation

•	Broken wire inside the insulation

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step will determine if DTC P0237 is the result of a hard failure or an intermittent condition.

This step simulates conditions for a DTC P0237. If the PCM recognizes the change, the PCM and signal circuit are OK.

In this step, components that share the 5 volt reference can cause the reference voltage to be shorted to ground. This can be checked by disconnecting each component that shares the 5 volt reference one at a time, including the PCM while checking for continuity on that circuit to chassis ground.

Step

Action

Values

Yes

Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and failure records for reference. The control modules data is deleted once the Clear Info function is used.

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Connect a scan tool.
Start the engine and let the engine idle.
Observe the Boost pressure display on the scan tool.

Does the scan tool display a Boost Pressure less than or equal to the specified value?

40 kPa

Go to Step 3

Go to Step 5

Turn the ignition OFF.
Disconnect the Boost sensor electrical connector.
Jumper the Boost sensor 5 volt reference to the Boost sensor signal circuit at the harness.
Turn the ignition ON.

Does the scan tool display a Boost Pressure more than or equal to the specified value?

202 kPa

Go to Step 6

Go to Step 4

Turn the ignition OFF.
The Boost sensor still disconnected.
Remove the jumper wire.
Probe the Boost sensor signal circuit at the harness with a test lamp connected to B+.
Turn the ignition ON.

Does the scan tool display a Boost Pressure more than or equal to the specified value?

202 kPa

Go to Step 8

Go to Step 7

The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If additional DTCs are stored, refer to those tables first.

Are any additional DTCs stored?

Go to applicable DTC

Go to Diagnostic Aids

Check for a proper connection at the Boost sensor.
If a problem is found, repair as necessary.

Was a problem found?

Go to Step 13

Go to Step 10

Check for the following in Boost sensor signal circuit.

•	For an open.

•	For a short to ground.

If a problem is found, repair as necessary.

Was a problem found?

Go to Step 13

Go to Step 11

Check for an open in the boost sensor 5 volt reference circuit.
If a problem is found, repair as necessary.

Was a problem found?

Go to Step 13

Go to Step 9

Check for a short to ground in the boost sensor 5 volt reference circuit.
If a problem is found, repair as necessary.

Was a problem found?

Go to Step 13

Go to Step 12

Replace the boost sensor. Refer to Boost Sensor Replacement .

Is the action complete?

Go to Step 13

Check the terminal connectors at the PCM for a proper connections.
If a problem is found, repair as necessary.

Was a problem found?

Go to Step 13

Go to Step 12

Important: The new PCM must be programmed.

Replace the PCM. Refer to Powertrain Control Module Replacement/Programming .

Is the action complete?

Go to Step 13

Using the scan tool, clear the DTCs.
Start the engine.
Allow the engine to idle at normal operating temperature.
Select DTC and the Specific DTC function.
Enter the DTC number which was set.
Operate the vehicle, with the Condition for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

Go to Step 14

Go to Step 2

Does the scan tool display any additional undiagnosed DTCs?

Go to applicable DTC

System OK