Two-Piece Propeller Shaft Replacement Inboard Slip Joint and Full

Removal Procedure

1. Block the wheels.
2. Support the propeller shaft.
3. Mark the universal joints and slip joints with alignment marks.
4. Remove the propeller shaft guards, if equipped.
5. Remove the propeller shaft from the Yoke Flange (8 nuts) mounting.
6. Remove the center bearing assembly from the cross member. Refer to Center Bearing Replacement .



7. Remove the two-piece propeller shaft mounting.



8. Remove the propeller shaft 16N, 17N, 18N, 1710 or 1760 series with inboard slip joint and flange yoke.

Installation Procedure

1. Support the propeller shaft sections in the installed position.
2. Install the slip yoke and the center bearing assembly to the installed propeller shaft splined end. Refer to Fluid and Lubricant Recommendations .



3. Install the front propeller shaft to the Yoke Flange (8 nuts) mounting. Keep the alignment marks together.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install and tighten the propeller shaft inboard slip joint and full round end yoke bolts. Refer to Fastener Tightening Specifications .

Tighten
Tighten the center bearing mounting bolts to 71 N·m (52 lb ft).

5. Install the rear propeller shaft to the center bearing assembly.
6. Install the center bearing assembly to the cross frame. Refer to Center Bearing Replacement .
7. Install the propeller shaft guards, if equipped.
8. Lubricate the universal joints and the slip joints. Refer to Fluid and Lubricant Recommendations .
9. Remove the wheel blocks.

Two-Piece Propeller Shaft Replacement Outboard Slip Joint and Half

Removal Procedure

1. Block the wheels.
2. Support the propeller shaft.
3. Mark the universal joints and slip joints with alignment marks.
4. Remove the propeller shaft guards, if equipped.
5. Remove the propeller shaft from the Yoke Flange (4 nuts) mounting.
6. Remove the center bearing assembly from the cross member. Refer to Center Bearing Replacement .



7. Remove the two-piece propeller shaft mounting.



8. Remove the propeller shaft 1480 or 1550 series with outboard slip joint and half round end yoke.

Installation Procedure

1. Support the propeller shaft sections in the installed position.
2. Install the slip yoke and the center bearing assembly to the installed propeller shaft splined end. Refer to Fluid and Lubricant Recommendations .



3. Install the front propeller shaft to the Yoke Flange (4 nuts) mounting. Keep the alignment marks together.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install and tighten the propeller shaft outboard slip joint and half round end yoke bolts. Refer to Fastener Tightening Specifications .

Tighten
Tighten the center bearing mounting bolts to 71 N·m (52 lb ft).

5. Install the rear propeller shaft to the center bearing assembly.
6. Install the center bearing assembly to the cross frame. Refer to Center Bearing Replacement .
7. Install the propeller shaft guards, if equipped.
8. Lubricate the universal joints and the slip joints. Refer to Fluid and Lubricant Recommendations .
9. Remove the wheel blocks.

Two-Piece Propeller Shaft Replacement Center Bearing, Half yoke

Removal Procedure

1. Block the wheels.
2. Support the propeller shaft.
3. Mark the universal joints and slip joints with alignment marks.
4. Remove the propeller shaft guards, if equipped.
5. Remove the propeller shaft from the Yoke Flange (4 nuts) mounting.
6. Remove the center bearing assembly from the cross member. Refer to Center Bearing Replacement .



7. Remove the two-piece propeller shaft mounting.



8. Remove the propeller shaft 1480 or 1550 series with outboard slip joint and half round end yoke.

Installation Procedure

1. Support the propeller shaft sections in the installed position.
2. Install the slip yoke and the center bearing assembly to the installed propeller shaft splined end.
3. Install the front propeller shaft to the Yoke Flange (4 nuts) mounting. Keep the alignment marks together.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install and tighten the propeller shaft half round end yoke bolts. Refer to Fastener Tightening Specifications .

Tighten
Tighten the center bearing mounting bolts to 71 N·m (52 lb ft).

5. Install the rear propeller shaft to the center bearing assembly.
6. Install the center bearing assembly to the cross frame. Refer to Center Bearing Replacement .



7. Install the propeller shaft guards, if equipped.
8. Lubricate the universal joints and the slip joints. Refer to Fluid and Lubricant Recommendations .

Two-Piece Propeller Shaft Replacement Inboard Slip Joint and Flange

Removal Procedure

1. Block the wheels.
2. Support the propeller shaft.
3. Mark the universal joints and slip joints with alignment marks.
4. Remove the propeller shaft guards, if equipped.
5. Remove the propeller shaft from the Yoke Flange (4 nuts) mounting.
6. Remove the center bearing assembly, if equipped, from the cross member. Refer to Center Bearing Replacement .



7. Remove the two-piece propeller shaft mounting.



8. Remove the propeller shaft 1480 or 1550 series with inboard slip joint and flange yoke.

Installation Procedure

1. Install the universal joints to the propeller shaft. Refer to Universal Joint Replacement .
2. Support the propeller shaft sections in the installed position.
3. Install the slip yoke and the center bearing assembly to the installed propeller shaft splined end.



4. Install the front propeller shaft to the Yoke Flange (4 nuts) mounting. Keep the alignment marks together.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install and tighten the propeller shaft inboard slip joint and flange yoke bolts. Refer to Fastener Tightening Specifications .

Tighten
Tighten the center bearing mounting bolts to 71 N·m (52 lb ft).

6. Install the rear propeller shaft to the center bearing assembly.



7. Install the center bearing assembly to the cross frame. Refer to Center Bearing Replacement .
8. Install the propeller shaft guards, if equipped.
9. Lubricate the universal joints and the slip joints. Refer to Fluid and Lubricant Recommendations .
10. Remove the wheel blocks.

Two-Piece Propeller Shaft Replacement Center Bearing, Full Yoke

Removal Procedure

1. Block the wheels.
2. Support the propeller shaft.
3. Mark the universal joints and slip joints with alignment marks.
4. Remove the propeller shaft guards, if equipped.
5. Remove the propeller shaft from the Yoke Flange (8 nuts) mounting.
6. Remove the center bearing assembly from the cross member. Refer to Center Bearing Replacement .



7. Remove the two-piece propeller shaft mounting.
8. Remove the universal joint. Refer to Universal Joint Replacement .



9. Remove the propeller shaft 16N, 17N, 18N, 1710, or 1760 series with center bearing and full round or end yoke.

Installation Procedure

1. Install the universal joints to the propeller shaft. Refer to Universal Joint Replacement .
2. Support the propeller shaft sections in the installed position.



3. Install the slip yoke and the center bearing assembly to the installed propeller shaft splined end.



4. Install the front propeller shaft to the Yoke Flange (8 nuts) mounting. Keep the alignment marks together.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install and tighten the propeller shaft full round end yoke bolts. Refer to Fastener Tightening Specifications .

Tighten
Tighten the center bearing mounting bolts to 71 N·m (52 lb ft).

6. Install the rear propeller shaft to the center bearing assembly.
7. Install the center bearing assembly to the cross frame. Refer to Center Bearing Replacement .

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

8. Inspect the propeller shaft for alignment and phasing.



9. Install the propeller shaft guards, if equipped.
10. Lubricate the universal joints and the slip joints. Refer to Fluid and Lubricant Recommendations .
11. Remove the wheel blocks.