Accessory Mounting Brackets Replacement With AC

1. Remove the engine cooling fan. Refer to Fan Replacement in Engine Cooling.
2. Remove the drive belt. Refer to Drive Belt Replacement .

Important: Do not evacuate the air conditioning system.

3. Remove the mounting bolts for the air conditioning compressor, if equipped. Refer to Body Manufacturers manual.
4. Move the compressor aside and support.
5. Remove the drive belt idler pulley if not equipped with A/C. Refer to Drive Belt Idler Pulley Replacement .
6. Remove the power steering pump pulley. Refer to Power Steering Pump Pulley Replacement in Power Steering.
7. Remove the power steering pump to the accessory mounting bracket. Refer to Power Steering Pump Replacement in Power Steering.



8. Remove the three bolts and nut holding the accessory mounting bracket to the engine.
9. Slide the bracket off the stud and power steering pump.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Slide the bracket on the stud and the power steering pump.
2. Install the three bolts and the nut.

Tighten
Tighten the bolts and nut to 44 N·m (32 lb ft).

3. Install the power steering pump. Refer to Power Steering Pump Replacement in Power Steering.
4. Install the power steering pump pulley. Refer to Power Steering Pump Pulley Replacement in Power Steering.
5. Install the air conditioning compressor, if equipped. Refer to Body Manufacturers manual.
6. Install the drive belt idler pulley if not equipped with A/C. Refer to Drive Belt Idler Pulley Replacement .
7. Install the drive belt. Refer to Drive Belt Replacement .
8. Install the engine cooling fan. Refer to Fan Replacement in Engine Cooling.

Accessory Mounting Brackets Replacement Generator

1. Remove the engine cooling fan. Refer to Fan Replacement in Engine Cooling.
2. Remove the drive belt. Refer to Drive Belt Replacement .
3. Remove the generator. Refer to Generator Replacement in Engine Electrical.
4. Remove the wire harness bracket from the generator mounting bracket.
5. Remove the drive belt tensioner. Refer to Drive Belt Tensioner Replacement .
6. Remove the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement .



7. Remove the three bolts and nut holding the generator bracket to the engine.
8. Slide the bracket off of the stud.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Slide the bracket on the stud.
2. Instal the three bolts and the nut.

Tighten
Tighten the bolts and nut to 41 N·m (30 lb ft).

3. Install the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement .
4. Install the drive belt tensioner. Refer to Drive Belt Tensioner Replacement .



5. Install the wire harness bracket to the generator mounting bracket.

Tighten
Tighten the bolt to 24 N·m (18 lb ft).

6. Install the generator. Refer to Generator Replacement in Engine Electrical.
7. Install the drive belt. Refer to Drive Belt Replacement .
8. Install the engine cooling fan. Refer to Fan Replacement in Engine Cooling.