Circuit Description
The PCM supplies a voltage of about 450 mV between the HO2S high and low signal circuits. The oxygen sensor varies the voltage over a range from about 1000 mV when the exhaust is rich, down through about 10 mV when the exhaust is lean.
The PCM monitors and stores the heated oxygen sensor (HO2S) voltage information. The PCM evaluates the HO2S voltage samples in order to determine the amount of time the HO2S voltage was out of range. The PCM compares the stored HO2S voltage samples taken within each sample period and determines if majority of the samples are out of the operating range.
The PCM monitors the HO2S voltage for being fixed below a predetermined voltage. If the PCM detects the voltage is below a predetermined voltage, this DTC will set.
Conditions for Running the DTC
Criteria 1
| • | DTCs P0102, P0103, P0112, P0113, P0117, P0118, P0335, P0336, P1120, P1220, P1221, not set. |
| • | The ignition voltage is greater than 9.0 volts. |
| • | The fuel system operating in Closed Loop. |
| • | The TP angle is between 10- 26 percent. |
Criteria 2
| • | DTCs P0102, P0103, P0112, P0113, P0117, P0118, P0335, P0336, P1120, P1220, P1221, not set. |
| • | The ignition voltage is greater than 9.0 volts. |
| • | The Power Enrichment mode is enabled for greater than 0.5 second. |
Conditions for Setting the DTC
Criteria 1
| • | The engine coolant temperature is greater than 60°C (140°F). |
| • | The fuel trim learn is enabled. |
| • | The air/fuel ratio is between 14.5:1-14.7:1. |
| • | The HO2S signal voltage remains below 200 mV. |
| • | The Criteria 1 conditions are present for 31 seconds. |
OR
| • | The HO2S signal voltage remains below 360 mV. |
| • | The Criteria 2 conditions are present for 4.5 seconds during the Power Enrichment mode. |
Action Taken When the DTC Sets
| • | The PCM illuminate the malfunction indicator lamp (MIL) on the second consecutive drive trip that the diagnostic runs and fails, if the diagnostic fails under the same conditions (load, RPM, temperature, etc.) as the previous ignition cycle that the test ran and failed. |
| • | The first time the diagnostic fails, the PCM records the operating conditions in Failure Records. |
| • | The second consecutive drive trip that this diagnostic fails under the same conditions (load, RPM, temperature, etc.) as the previous ignition cycle that the test ran and failed, the PCM stores this information in Freeze Frame. The PCM copies any data previously stored in Freeze Frame and copies the data into the Failure Records. The PCM then overwrites the Freeze Frame and the PCM updates the HO2S data in the Failure Records. |
| • | Open Loop Fueling. |
Conditions for Clearing the MIL/DTC
| Important: If the last failure was during a non-typical driving condition, the MIL may remain ON longer than the three drive trips. Review the Freeze Frame and Failure Records for the last failure conditions. |
| • | The PCM turns the MIL OFF after 3 consecutive drive trips that the diagnostic runs and does not fail within the same conditions that the DTC last failed. |
| • | A History DTC clears after 40 consecutive warm-up cycles, if this or any other emission related diagnostic does not report any failures. |
| • | A last test failed (Current DTC) clears when the diagnostic runs and does not fail. |
| • | The PCM battery voltage is interrupted. |
| • | Use a scan tool in order to clear the MIL/DTC. |
Diagnostic Aids
Important: Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing/replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.
| • | Heated Oxygen Sensor (HO2S) wire: Sensor pigtail may be in contact with the exhaust manifold or the exhaust system. |
| • | An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provides the supply of oxygen. Inspect the HO2S wires and connections for breaks or contamination. Refer to Wiring Repairs |
| • | Check for intermittent ground in signal wire between connector and sensor. |
| • | Lean injector(s): Perform the Injector Balance Test. |
| • | Fuel contamination: Water near the in-tank fuel pump inlet can be delivered to the injectors. The water causes a lean exhaust and can set a DTC. |
| • | Fuel pressure: System will be lean if fuel pressure is low. Refer to Fuel System Diagnosis |
| • | Exhaust leaks: An exhaust leak near the HO2S can cause a lean condition. |
| • | Vacuum or crankcase leaks can cause a lean condition. |
| • | If the above are OK, the HO2S may be at fault. |
For an intermittent condition, refer to Symptoms .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
If the HO2S voltage is fix well below 200 Mv, this indicates a short to battery ground or chassis ground. If the voltage is fix near or above 200 Mv, this indicates a short to a PCM ground. When the HO2S voltage is fix near 200 Mv, indicates the DTC set when the fuel system was in a Power Enrichment mode of operation.
The engine must be at the normal operating temperature before performing this test. For any test that requires probing the PCM or a component harness connector, use the Connector Test Adapter Kit J 35616 . Using this kit prevents damage to the harness connector terminals.
-
Using the Freeze Frame and/or Failure Records data may aid in locating an intermittent condition. If you can not duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data can help determine how many miles since the DTC set. The Fail Counter and Pass Counter can also be used to determine how many ignition cycles the diagnostic reported a pass and/or a fail. Operate the vehicle within the same freeze frame conditions (RPM, load, vehicle speed, temperature etc.) that the PCM recorded. This will isolate when the DTC failed.
-
Grounding the low side circuit of the HO2S should cause the HO2S voltage to display a bias voltage. A voltage staying near 0.0 volts indicates the low circuit is open, or the high circuit is open or grounded.
-
Disconnecting the PCM allows using a DMM J 39200 in order to check continuity of the circuits. This aids in locating an open or shorted circuit.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
|
Important: Check the HO2S for being secure before proceeding with this DTC. A sensor that is loose could cause this DTC to set.
Is the HO2S voltage less than the specified value? | 200 mV | |||
Does the scan tool indicate that this diagnostic failed this ignition? | -- | Go to Diagnostic Aids | ||
Does the scan tool indicate HO2S voltage within the specified range? | 350-550 mV | Go to Diagnostic Aids | ||
Is the HO2S signal circuit shorted? | -- | |||
6 | Repair the HO2S signal circuit. Refer to Wiring Repairs Is the action complete? | -- | -- | |
7 |
Important:: Program the replacement PCM. Replace the PCM. Refer to Powertrain Control Module Replacement . Is the action complete? | -- | -- | |
8 |
Does the scan tool indicate that this test ran and passed? | -- | ||
9 | Select the Capture Info option and the Review Info option using the scan tool. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to the applicable DTC table | System OK |
