Circuit Description (DTC C0265/C0266)
The pump motor relay supplies power to all eight solenoid coils (four isolation solenoid coils and four dump solenoid coils) and the pump motor when the ABS is required. The relay and the eight solenoid coils are located within the EBCM.
Conditions for Setting the DTC (DTC C0265)
| • | The EBCM microprocessor commands the relay on. |
| • | Low voltage exists on all eight solenoid driver circuits when high voltage is expected (the solenoid is not energized). |
Conditions for Setting the DTC (DTC C0266)
| • | The ABS bulb check is complete. |
| • | High voltage exists on the eight solenoid circuits when all are expected to be low (the relay is not commanded on). |
Action Taken When the DTC Sets
| • | The ABS indicator lamp turns on. |
| • | The ABS disables. |
DTCs C0265-C0266 are Ignition Latched DTCs, which indicates that the above actions remain true until the ignition is turned to OFF (even if the cause of the DTC is intermittent).
Conditions for Clearing the DTC
| • | Repair the conditions responsible for setting the DTC. |
| • | Use the Scan Tool Clear DTCs function. |
Diagnostic Aids (DTC C0265)
DTC C0265 usually sets because of an open relay coil or non-closable relay contacts. The relay is located within the EBCM. The relay is not serviceable. If the test does not repair the DTC, then replace the EBCM.
If DTC C0265 appears with other DTCs repair the other DTCs first. Clear all DTCs. Then run three function tests with the Scan Tool . Refer to this diagnostic chart if DTC C0265 resets.
Diagnostic Aids (DTC C0266)
DTC C0266 usually sets when the relay contacts are stuck closed. The relay is located within the EBCM. The relay is not serviceable. If the test does not repair the DTC, then replace the EBCM.
Test Description
The numbers below refer to the steps in the diagnostic table:
-
This step checks the resistance of the ground circuit.
-
This step checks the ignition voltage available to the EBCM.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | Go to Step 2 | |
2 |
Is the connector in good condition? | -- | Go to Step 3 | Go to Step 7 |
Using the J 39200 , measure the resistance between terminal 2 of the 2-way EBCM harness connector and ground . Is the resistance measurement within the specified range? | 0-2 ohms | Go to Step 4 | Go to Step 8 | |
Is the voltage measured equal to or greater than the specified value? | 10 V | Go to Step 6 | Go to Step 5 | |
5 | Inspect the 60-amp ABS fuse. Is the fuse open? | -- | Go to Step 10 | Go to Step 11 |
6 |
Does the DTC set as a current DTC? | -- | Go to Step 9 | Go to Diagnostic Aids |
7 | Repair the 2-way EBCM harness connector if necessary. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | -- | |
8 | Repair the open or the high resistance in CKT 150. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | -- | |
9 | Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Is the repair complete? | -- | -- | |
10 | Repair the short to ground in CKT 142. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | -- | |
11 | Repair the open or high resistance in CKT 142. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | -- |
