Important: If steering stops are adjusted such that a minimum of 1-3/4 steering
wheel turns from straight ahead position is not available, the poppets are
not functional nor can they be adjusted to function.
- Set the steering stops to the vehicle manufacturer's specifications.
Allow for the revisions from the original equipment installation.
- Turn the special service poppet adjusting screw (1) into the
non-sealing end of the service sealing jam nut until the drive end
of the screw is flush with the nut.
- Verify that the following conditions exist:
| • | The vehicle is unloaded. |
| | Important: With the road wheels in the straight ahead position, the steering gear
is in the center position when the timing marks on the end of the sector shaft
and housing trunnion are aligned.
|
| • | The wheels are in the straight ahead position. |
- Use a 5/8 socket in order to remove the following components
from the lower end of the housing:
| • | The poppet fixed stop screw |
- Discard the screw and the washer.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
Important: It may be necessary to move the sector shaft slightly from the straight
ahead position to assemble the service adjusting screw (1) as instructed.
Return the sector shaft to the straight ahead position after the
assembly.
- Turn the screw (2) and the nut (3) assembly into the housing until the
nut is firmly against the housing.
Do not rotate the nut (3) on the screw (2).
Tighten
Tighten the sealing nut to 54 N·m (40 lb ft).
- Refill the pump reservoir with approved power steering fluid.
Important: Note which steering wheel rotation direction is required in order to
position the rack piston (3) toward the adjusting screw (1).
- Use the following steps in order to preset the upper poppet adjuster
seat and sleeve assembly:
| 8.1. | Observe the end of the sector shaft for direction of travel. Note
the direction of travel in order to position the rack piston (3) when the
poppets (9, 4) are reset. |
| 8.3. | Rotate the steering wheel in either the clockwise or the counterclockwise
direction. Locate the sector shaft toward the end of the steering travel. |
| 8.4. | Place the steering stop bolt against the steering stop in order
to position the rack piston toward the adjustable poppet screw (1) at the
closed end of the housing. |
| | Important: If excess input torque or rim pull is encountered at the steering wheel
prior to reaching the steering stop, allow the vehicle to roll slowly forward
while rotating the steering.
|
| 8.5. | Continue to rotate the steering wheel until the following conditions
are met: |
| • | The steering stops are contacted. |
| • | A correct input torque is reached. |
| • | The initial internal engagement of the poppet adapter seat and
sleeve (5, 10) and the adjusting screw is felt. |
| • | There is a torque rise at the steering wheel. |
| 8.6. | Tighten the input torque. |
Tighten
Tighten the input torque of 54 N·m (40 lb ft)
at the steering wheel nut or 48 lb (21.8 kg) rim pull on a 508 mm
(20 in) steering wheel is reached.
- Turn the steering wheel at least 13/4 steering wheel turns
from the straight ahead position.
This action completes the internal preset of the upper poppet adjuster
seat and sleeve assembly (10).
- Loosen the sealing nut
(3).
- Back out the adjusting screw (1) until 25.4-27.4 mm
(1.00-1.06 in) (1) of the screw (1) is beyond the sealing
nut (3).
- Torque the nut firmly against the housing. Maintain the clearance
of 25.4-27.4 mm (1.00-1.06 in).
Tighten
Tighten the sealing nut to 54 N·m (40 lb ft).
- Measure the adjusting screw (2).
Ensure that the adjusting screw (2) does not protrude more than 27 mm
(1.06 in) beyond the nut (1).
Important: If excess input torque or rim pull is encountered at the steering wheel
prior to reaching the steering stop, allow the vehicle to roll slowly forward
while rotating the steering wheel.
- Use the following steps in order to position the upper poppet valve
to the related axle stop:
| 14.1. | Ensure that the vehicle is unloaded. |
| 14.3. | Turn the steering wheel toward full travel in the opposite direction. |
| 14.4. | Turn the axle until the axle bottoms against the steering stop. |
Do not apply more than 33.9 N·m (25 lb ft)
or 30 lb (13.6 kg) rim pull on a 508 mm (20 in)
diameter steering wheel.
Notice: At no time should system relief pressure be maintained for longer than
5 seconds, as damage to the steering pump may result.
- Use the following steps
in order to return the system to the system relief pressure:
| 15.1. | Turn the steering wheel toward full travel in the opposite direction. |
Rotate the steering wheel until contact is made with the steering stop.
| 15.2. | Position the rack piston (3) toward the poppet adjusting screw
(1) at the closed end of the housing. |
Notice: Do not exceed the 2.3 N·m (20 lb in) maximum
torque increase on adjusting screw during step 10, since excessive screw torque
could upset the position of the poppets in the rack piston previously achieved
to control the upper poppet pressure relief. That would necessitate the repetition
of these entire procedures.
- Hold the steering wheel
in the steering stop contact position.
Loosen the sealing nut (3) one turn.
- Turn the adjusting screw (2) while holding the sealing nut (3).
Continue to turn the adjusting screw until the adjusting screw (2) torque
increases by 1.1-2.3 N·m (10-20 lb in).
- Back out the screw (2) by 4 turns.
- Release the steering wheel.
- Hold the adjusting screw in place.
Tighten the sealing nut (3) firmly against the housing.
Tighten
Tighten the sealing nut to 54 N·m (40 lb ft).
| | Caution: The 27 mm (1.06 in) maximum adjusting screw protrusion
from the sealing nut must not be exceeded to ensure adequate screw thread
engagement in housing. Inadequate screw engagement could cause loss of the
adjusting screw during operation. This could result in loss of power steering
and possible personal injury.
|
| 20.1. | If the adjusting screw extends more than 27 mm (1.06 in)
from the sealing nut, loosen the sealing nut. |
| 20.2. | Turn the adjusting screw until a length of 27 mm (1.06 in)
is achieved. |
| 20.3. | Tighten the sealing nut (3) again. |
Important: Repeat the adjustment procedure when the following conditions exist:
| • | The service adjustable poppet screw and the nut are in place. |
| • | The manual adjustment is complete. |
For automatic adjustment, turn the adjusting screw into the nut in order
to duplicate the original fixed stop screw end position.
- The manual poppet valve readjustment is now completed.
