Air Brake Automatic Slack Adjuster Replacement Rockwell

Important: For unit repair information on the Rockwell air brake automatic slack adjuster contact the Rockwell Field Support Center at 1-800-535-5560.

1. Block the wheels.
2. Cage the rear air brake chambers. Refer to Caging the Rear Air Brake Chamber in Air Brakes.
3. Drain all air reservoirs. Refer to Draining Reservoirs .
4. Raise and support the vehicle with safety stands. Refer to Lifting and Jacking the Vehicle in General Information.



5. Mark the position of the air brake automatic slack adjuster to the camshaft by drawing a straight line on both parts.



6. Remove the retainers.
7. Remove the air brake chamber clevis pins.



8. Fully release the air brake automatic slack adjuster using the following steps:

8.1.	Disengage the pawl with a screwdriver.

8.2.	Turn the air brake automatic slack adjuster adjusting nut until the air brake automatic slack adjuster is free from the air brake chamber clevis.

8.3.	Release the pawl so that the pawl snaps into engagement.




9. Remove the camshaft snap ring.



10. Remove the camshaft washers (9).
11. Remove the air brake automatic slack adjuster (4).



12. Check the air brake automatic slack adjuster adjusting nut torque using the following steps:

12.1.

Use a pound/inch torque wrench in order to rotate the air brake automatic slack adjuster adjusting nut counterclockwise.

12.2.

Turn the air brake automatic slack adjuster gear 360 degrees, 22 rotations of the air brake automatic slack adjuster adjusting nut. The torque must remain less than 4.5 N·m (40 lb in). Overhaul or replace the air brake automatic slack adjuster if the torque specification is exceeded.




13. Inspect the air brake chamber clevis pins for wear or damage.

Replace the air brake chamber clevis pins if necessary.




14. Measure the bushing in the arm of the air brake automatic slack adjuster (4).

Replace the bushings if the diameter exceeds 13.5 mm (0.531 in).

1. Install the air brake automatic slack adjuster to the camshaft (12).
2. Install the camshaft washer(s) (13).



3. Install the camshaft snap ring.



4. Disengage the pawl assembly with a screwdriver.



5. Turn the slack adjuster adjusting nut until the slack adjuster arm is properly aligned with the holes in the clevis.
6. Release the pawl so that the pawl snaps into engagement.



7. Align the marks made on the air brake automatic slack adjuster and the camshaft.
8. Fully release the air brake automatic slack adjuster.
9. Install the air brake chamber clevis pins.
10. Install the New retainers.
11. Adjust the brakes. Refer to Air Drum Brake Adjustment .
12. Remove the safety stands and lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
13. Uncage the rear air brake chambers. Refer to Caging the Rear Air Brake Chamber .
14. Check for proper brake operation.
15. Apply the parking brake.
16. Remove the wheel blocks.

Air Brake Automatic Slack Adjuster Replacement Eaton

Important: Service the Eaton® air brake automatic slack adjuster by replacement only.

1. Block the wheels.
2. Cage the rear air brake chambers. Refer to Caging the Rear Air Brake Chamber .
3. Drain all air reservoirs. Refer to Draining Reservoirs in Air Brakes.



4. Remove the retainer.
5. Remove the air brake chamber clevis pin cotter pin.
6. Remove the air brake chamber clevis pin.
7. Fully release the slack adjuster by turning the slack adjuster counterclockwise until the slack adjuster arm is free from the clevis.



8. Remove the air brake automatic slack adjuster control arm nut and the washer.



9. Remove the camshaft snap ring.



10. Remove the camshaft washer(s) (5).
11. Remove the air brake automatic slack adjuster (4).
12. Inspect the air brake automatic slack adjuster (4) for damage or excessive wear.

Replace the air brake automatic slack adjuster (4) if damage or excessive wear is present.

1. Lubricate the camshaft splines. Use the Anti-Seize Lubricant GM P/N 1052771 or equivalent.
2. Install the air brake automatic slack adjuster (4) to the camshaft.
3. Install the camshaft washer(s) (5).



4. Install the camshaft snap ring.



5. Loosely install the air brake automatic slack adjuster control arm washer.
6. Loosely install the air brake automatic slack adjuster control arm nut.



7. Rotate the air brake automatic slack adjuster adjusting hex clockwise until the air brake automatic slack adjuster arm hole aligns with the air brake chamber clevis hole.



8. Install the air brake chamber clevis pin.

Do not install the retainer at this time.

9. Remove the air brake chamber clevis pin later in order to check installation.




Notice: Excessive positioning force may damage the air brake automatic slack adjuster control arm. Most adjusters will be equipped with an installation indicator. The indicator must fall within the slot for proper installation. Incorrect air brake automatic slack adjuster control arm position can cause tight or dragging brakes.

10. Adjust the slack adjuster control arm by rotating the arm counterclockwise.

Rotate away from the slack adjuster adjusting hex and towards the air brake chamber. Continue rotating until the air brake control arm comes to a definite internal stop. If necessary, use a plastic mallet in order to tap the slack adjuster control arm into position.





Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: Ensure that the air brake automatic slack adjuster control arm does not move from the correct position while tightening the air brake automatic slack adjuster control arm nut.

11. Tighten the slack adjuster control arm nut.

Tighten
Tighten the slack adjuster control arm nut to 17 N·m (13 lb ft).

12. Adjust the brakes. Refer to Air Drum Brake Adjustment .
13. Start the engine.
14. Charge the system to the air compressor governor valve cut-out point.
15. Stop the engine.
16. Inspect the slack adjuster for the proper installation.
17. Verify that the installation indicator is within the slot.



18. Remove the air brake chamber clevis pin.
19. Align the air brake chamber clevis hole and the air brake automatic slack adjuster arm hole.
20. Repeat steps 7 through 17 if the air brake chamber clevis retracts towards the air brake chamber when you remove the air brake chamber clevis pin.
21. Install the air brake chamber clevis pin.
22. Install the air brake chamber clevis pin cotter pin.



23. Check the air brake automatic slack adjuster adjusting hex torque.
24. Use a pound/inch torque wrench in order to rotate the air brake automatic slack adjuster adjusting hex counterclockwise.
25. The air brake automatic slack adjuster clutch should not slip at a torque less than 18 N·m (13 lb ft).

A racheting sound occurs when the clutch slips. Replace the air brake automatic slack adjuster if the clutch slips at a lesser torque.

26. Start the engine.
27. Charge the system to the air compressor governor valve cut-out point.
28. Stop the engine.
29. Uncage the air brake chambers. Refer to Caging the Rear Air Brake Chamber .
30. Check for the proper brake operation.
31. Apply the parking brake.
32. Remove the wheel blocks.