GM Service Manual Online
For 1990-2009 cars only

Evaporative Emission Canister Vent Solenoid Valve Replacement Cab/Chassis

Removal Procedure

  1. Raise the Vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  2. Object Number: 669555  Size: SH
  3. Disconnect the EVAP vent pipe from the EVAP canister vent valve.
  4. Disconnect the EVAP vent harness connector from the EVAP canister vent valve.
  5. Remove the EVAP vent bracket retaining bolt from the crossmember.
  6. Remove the EVAP canister vent valve.
  7. Remove the EVAP vent bracket from the EVAP canister vent valve.

Installation Procedure

  1. Install the EVAP vent bracket on the EVAP canister vent valve.

  2. Object Number: 669555  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the EVAP vent valve on the crossmember.
  4. Tighten
    Tighten the EVAP vent bracket retaining bolt to 12 N·m (106 lb in).

  5. Connect the EVAP vent harness connector to the EVAP canister vent valve.
  6. Connect the EVAP vent pipe to the EVAP canister vent valve.
  7. Lower the vehicle.

Evaporative Emission Canister Vent Solenoid Valve Replacement Utility

Removal Procedure


    Object Number: 627189  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Disconnect the vent pipe (2) from the evaporative emission (EVAP) canister vent valve.
  3. Disconnect the EVAP canister vent valve electrical connector (3).
  4. Detach the EVAP canister vent valve from the EVAP canister vent valve bracket (1).

Installation Procedure


    Object Number: 627189  Size: SH
  1. Install the EVAP canister vent valve to the EVAP canister vent valve bracket (1).
  2. Connect the EVAP canister vent valve electrical connector (3).
  3. Connect the vent pipe (2) to the EVAP canister vent valve.
  4. Lower the vehicle.

Evaporative Emission Canister Vent Solenoid Valve Replacement Utility Vent Pipe

Removal Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  2. Object Number: 625803  Size: SH
  3. Disconnect the EVAP vent pipe (3) from the EVAP canister vent valve.
  4. Disconnect the vent pipe (3) from the EVAP canister.
  5. Disconnect the vent pipe from the retaining clips (5) located on the fuel tank.
  6. Remove the EVAP vent pipe.

Installation Procedure


    Object Number: 625803  Size: SH
  1. Position the EVAP vent pipe (3) on the fuel tank.
  2. Connect the EVAP vent pipe (3) to the retaining clips (5) on the fuel tank.
  3. Connect the EVAP vent pipe (3) to the EVAP canister.
  4. Connect the EVAP vent pipe (3) to the EVAP canister vent valve.
  5. Lower the vehicle.

Evaporative Emission Canister Vent Solenoid Valve Replacement Pickup

Replacement Procedure

  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Disconnect the evaporative emission (EVAP) canister vent electrical connector, if equipped.
  3. Disengage the 2 vent valve pipe clips securing the pipe to the underbody.
  4. Remove the clips from the underbody and discard.

  5. Disconnect the vent valve pipe at the EVAP canister.
  6. Remove and retain the EVAP canister vent valve bracket mounting bolt.
  7. Remove the complete EVAP canister vent valve assembly with bracket attached and discard.
  8. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1962414  Size: SH

    Important: The new canister vent valve will be installed in a new location, outside of the frame.

  9. Position and secure the new valve assembly to the frame bracket on the outside of the frame using the existing hole and mounting bolt.
  10. Tighten
    Tighten the bracket mounting bolt to 12 N·m (106 lb in).

  11. Connect the vent valve pipe to the EVAP canister.
  12. Install the 2 vent valve pipe clips into the existing underbody holes.
  13. Connect the EVAP canister vent valve electrical connector, if equipped.
  14. Attach a bulk 5/8 in heater hose to the vent valve port and secure using a clamp.
  15. Cut the hose to determined length and install the supplied filter box. Secure using a clamp.

  16. Object Number: 1962416  Size: SH
  17. Secure the filter box to the fuel lines above the transmission using a tie strap.
  18. The filter box opening should be pointing downward.

  19. Tie strap the hose as needed along the frame rail in order to keep the hose away from the pinch-points and heat sources.
  20. Lower the vehicle.