The torque converter clutch pulse width modulation (TCC PWM) solenoid valve controls fluid acting on the converter clutch valve, which then controls TCC apply and release. The TCC PWM solenoid valve attaches to the control valve body within the transmission. Ignition voltage goes directly to the TCC PWM solenoid valve. The powertrain control module (PCM) controls the TCC PWM solenoid valve by providing a ground path on the control circuit. The current flows through the TCC PWM solenoid valve coil according to the duty cycle (percentage of ON time). The TCC PWM solenoid valve provides a smooth engagement of the torque converter clutch by operating on a duty cycle percent of ON time.
If the PCM detects a continuous open or short in the TCC PWM solenoid valve circuit or the TCC PWM solenoid valve, then DTC P1860 sets. DTC P1860 is a type C DTC. For California emission vehicles and vehicles under 8600 GVW, DTC P1860 is a type B DTC.
• | The system voltage is 8.0-18.0 volts. |
• | The engine is running greater than 400 RPM for greater than 7 seconds. |
All conditions for running the DTC are met, and either of the following conditions occur for 4.3 out of 5 seconds.
• | The PCM commands the TCC PWM solenoid valve to OFF (0 percent) and the voltage input remains low (zero volts). |
• | The PCM commands the TCC PWM solenoid valve to ON (100 percent) and the voltage input remains high (B+). |
• | For California emission equipped vehicles, the PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
• | The PCM inhibits TCC engagement. |
• | The PCM commands increased line pressure. |
• | The PCM freezes shift adapts from being updated. |
• | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame (Calif. only) and Failure Records (Calif. and Federal). |
• | The PCM stores DTC P1860 in PCM history. |
• | For California emissions, the PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
• | A scan tool can clear the MIL/DTC. |
• | For California emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring. |
• | For Federal emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
• | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
DTC P1860 defaults to an elevated line pressure condition which may result in TCC partial apply. This may induce idle surge and engine stall.
The numbers below refer to the step numbers on the diagnostic table.
This step tests for voltage to the TCC PWM solenoid valve circuit at the 20-way connector.
This step tests the ability of the PCM and wiring to control the ground circuit.
This step tests the resistance of the TCC PWM solenoid valve and the internal wiring harness.
Step | Action | Value(s) | Yes | No | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Diagnostic System Check - Engine Controls (6.0 L) or Diagnostic System Check - Engine Controls (8.1 L) in Engine Controls | |||||||||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Is the fuse open? | -- | ||||||||||||
3 | Inspect the following components for a short to ground.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Intermittent Conditions in Engine Controls | |||||||||||
Does the test lamp illuminate? | -- | |||||||||||||
5 | Repair the open or high resistance in the Off/Run/Crank voltage circuit (CKT 1020) of the TCC PWM solenoid valve. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | -- | |||||||||||
Does the test lamp turn ON when you command the TCC PWM solenoid valve ON, and does the lamp turn OFF when you command the TCC PWM solenoid valve OFF? | -- | |||||||||||||
7 |
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||||||
Does the resistance measure within the specified values? | 10-15 ohms | |||||||||||||
9 | Replace the PCM. Refer to Powertrain Control Module Replacement (6.0 L) or Powertrain Control Module Replacement (8.1 L) in Engine Controls. Did you complete the replacement? | -- | -- | |||||||||||
10 |
Does the resistance measure within the specified values? | 10-15 ohms | ||||||||||||
11 | Measure the resistance between terminal S and ground. Does the resistance measure greater than the specified value? | 250 K ohms | ||||||||||||
12 | Test the automatic transmission wiring harness assembly for an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find a condition? | -- | -- | |||||||||||
13 |
Do both readings measure greater than the specified value? | 250 K ohms | ||||||||||||
14 | Measure the resistance between terminal S and all other terminals, except terminals A, B, and E of the J 44152 . Refer to Automatic Transmission Inline Harness Connector End View . Is the resistance between terminal S and any other terminal, except terminals A, B, and E less than the specified value? | -- | Go to Intermittent Conditions in Engine Controls | |||||||||||
15 | Test the automatic transmission wiring harness assembly for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find a condition? | -- | -- | |||||||||||
16 | Replace the TCC PWM solenoid valve. Refer to Control Valve Body Replacement . Did you complete the replacement? | -- | -- | |||||||||||
17 | Replace the automatic transmission wiring harness assembly. Refer to Wiring Harness Replacement. Did you complete the replacement? | -- | -- | |||||||||||
18 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |