GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 396828  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the transfer case shield (if equipped). Refer to Transfer Case Shield Replacement .
  3. Drain the transfer case. Refer to Transfer Case Fluid Replacement .
  4. Remove the rear propeller shaft from the transfer case.
  5. • For vehicles equipped with a one piece propeller shaft, refer to One-Piece Propeller Shaft Replacement in Propeller Shaft.
    • For vehicles equipped with a two piece propeller shaft, refer to Two-Piece Propeller Shaft Replacement in Propeller Shaft.
  6. Remove the front propeller shaft from the transfer case. Refer to Front Propeller Shaft Replacement in Propeller Shaft.

  7. Object Number: 715667  Size: SH
  8. Remove the vent hose from the transfer case.

  9. Object Number: 662044  Size: SH
  10. Remove the electrical connector from the speed sensor.
  11. Support the transmission with a suitable jack stand.

  12. Object Number: 648001  Size: SH
  13. Remove the transmission mount from the crossmember.

  14. Object Number: 652595  Size: SH
  15. Remove the rear transmission crossmember.
  16. Install a suitable transmission jack to the transfer case.
  17. Remove the bolts from the transfer case to the adapter.

  18. Object Number: 648037  Size: SH

    Important: When performing this service procedure, pull straight back on the transfer case so that it is in a position so that it can be turn to a parallel to the transmission.

  19. Remove the transfer case from the transfer case adapter.
  20. Rotate the transfer case so that it is perpendicular to the torsion bar mounting bracket.
  21. Lower the transfer case.

  22. Object Number: 654219  Size: SH
  23. Remove the gasket from the transfer case.
  24. Remove transfer case from the transmission jack.

Installation Procedure


    Object Number: 654219  Size: SH
  1. Install the transfer case on a suitable transmission jack.
  2. Important: When installing a new transfer case gasket, make sure that the locating tab is pointing up for proper installation. Install the gasket without the use of any type of sealant or grease.

  3. Install a new transfer case gasket.
  4. Rotate that transfer case so that it is parallel to the torsion bar mounting bracket.
  5. Raise the transfer case into position.

  6. Object Number: 648037  Size: SH
  7. Rotate the transfer case so that it is in line with the adapter.
  8. Install the transfer case on the adapter.

  9. Object Number: 648011  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  10. Install the mounting nuts for the transfer case.
  11. Tighten
    Tighten the mounting nuts to 50 N·m (36 lb ft).


    Object Number: 652595  Size: SH
  12. Install the transmission support member.
  13. Tighten
    Tighten the crossmember mounting bolts to 70 N·m (51 lb ft).


    Object Number: 648001  Size: SH
  14. Install the transmission mount to the transfer case.
  15. Remove the transmission jack.
  16. Install the electrical connector to the speed sensor.

  17. Object Number: 715667  Size: SH
  18. Install the vent hose to the vent tube.
  19. Install the front propeller shaft. Refer to Front Propeller Shaft Replacement in Propeller Shaft.
  20. Install the rear propeller shaft.
  21. • For vehicle equipped with a one piece propeller shaft, refer to One-Piece Propeller Shaft Replacement in Propeller Shaft.
    • For vehicles equipped with a two piece propeller shaft, refer to Two-Piece Propeller Shaft Replacement in Propeller Shaft.
  22. Fill the transfer case with the proper transfer case fluid. Refer to Transfer Case Fluid Replacement .

  23. Object Number: 396828  Size: SH
  24. Install the transfer case shield. Refer to Transfer Case Shield Replacement .
  25. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.